Thanks Keith, I have the top part of the page ok. It was were to go for Inp 63 and inp 64.
Thanks Keith O.
Search found 10 matches
- Tue Jan 28, 2020 2:13 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Spindle parameters
- Replies: 2
- Views: 1702
Re: Spindle parameters
This post has been liked 0 time(s).
- Sun Jan 26, 2020 1:02 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 410 X axis (1) position error < solved >
- Replies: 8
- Views: 3282
Re: 410 X axis (1) position error < solved >
Hello Marty , The problem with the brake was the wrong software was installed in my kit. Standard instead of BP boss.
When Josh installed BP boss the machine was happy.
Machine is up and running now. I air cut a program Friday night, 33 minutes long and the rotation of the spindle was the only ...
When Josh installed BP boss the machine was happy.
Machine is up and running now. I air cut a program Friday night, 33 minutes long and the rotation of the spindle was the only ...
This post has been liked 0 time(s).
- Fri Jan 24, 2020 3:31 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Spindle parameters
- Replies: 2
- Views: 1702
Spindle parameters
Iam having trouble finding where to enter values for inp 63 and inp 64.
Thanks Keith.
Thanks Keith.
This post has been liked 0 time(s).
- Fri Jan 24, 2020 1:02 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: spindle set up
- Replies: 0
- Views: 3857
spindle set up
I need instructions to set up my spindle.
Bridgeport V2XT.
Encoder on spindle 1:1, 8000 count.
Air motor for speed up and down.
High, lo gear switch. Lo gear ratio 8.92:1
System I.D. 1217192326. serial# 900799.
I don't know how much, if any was set up in the Allin1 kit you guys sent me.
I am all ...
Bridgeport V2XT.
Encoder on spindle 1:1, 8000 count.
Air motor for speed up and down.
High, lo gear switch. Lo gear ratio 8.92:1
System I.D. 1217192326. serial# 900799.
I don't know how much, if any was set up in the Allin1 kit you guys sent me.
I am all ...
This post has been liked 0 time(s).
- Fri Jan 24, 2020 9:46 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 410 X axis (1) position error < solved >
- Replies: 8
- Views: 3282
Re: 410 X axis (1) position error < solved >
Thanks for the information, but I have no idea what to do with it. If you could hold my hand and walk me through it I would appreciate it so much.
I have no experience using computers this way. I thought I was doing well by posting a report. LOL.
Thanks Keith.
I have no experience using computers this way. I thought I was doing well by posting a report. LOL.
Thanks Keith.
This post has been liked 0 time(s).
- Mon Jan 20, 2020 6:51 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 410 X axis (1) position error < solved >
- Replies: 8
- Views: 3282
Re: 410 X axis (1) position error
Problem solved,Thanks to a post in march 2018 by Randy L.
I switched the D.C. wires to the servos at the Allin1 board. every thing is ok for now.
I for got to mention in my post the motors would rev up fast for 15 - 30 seconds then fault out. The motors turned smooth.
I was not in incremental ...
I switched the D.C. wires to the servos at the Allin1 board. every thing is ok for now.
I for got to mention in my post the motors would rev up fast for 15 - 30 seconds then fault out. The motors turned smooth.
I was not in incremental ...
This post has been liked 0 time(s).
- Mon Jan 20, 2020 1:45 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 410 X axis (1) position error < solved >
- Replies: 8
- Views: 3282
410 X axis (1) position error < solved >
I am installing an Allin1dc in my 1990 Bridgeport V2XT milling machine. I received the kit Jan. 3 2020 and the install was going great until Chapter 6,Final software configuration.
I am to jog the axis, I get a 410 X axis (1) position error. the same + or- jog on X ,Y , and Z axis. I tried 10%, 1 ...
I am to jog the axis, I get a 410 X axis (1) position error. the same + or- jog on X ,Y , and Z axis. I tried 10%, 1 ...
This post has been liked 0 time(s).
- Mon Jan 13, 2020 1:57 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Hi-lol gear switch
- Replies: 1
- Views: 1280
Hi-lol gear switch
I need a little help wiring the hi-lo switch.
I have a Bridgeport V2XT and installing an all in one cnc control. The wiring diagram shows a two wire switch, my Bridgeport has a three wire proximity switch.
Thanks for any help,Keith.
I have a Bridgeport V2XT and installing an all in one cnc control. The wiring diagram shows a two wire switch, my Bridgeport has a three wire proximity switch.
Thanks for any help,Keith.
This post has been liked 0 time(s).
- Wed Dec 11, 2019 2:51 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: V2xt limit switch.
- Replies: 7
- Views: 3988
Re: V2xt limit switch.
Thanks every one for your help. I am excited to get my mill retrofitted with the allinone.
Marty, your videos will be a big help and I thank you for your time.
Thanks Keith O.
Marty, your videos will be a big help and I thank you for your time.
Thanks Keith O.
This post has been liked 0 time(s).
- Tue Dec 10, 2019 4:27 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: V2xt limit switch.
- Replies: 7
- Views: 3988
V2xt limit switch.
I am buying the allinone kit for my Bridgeport V2xt tomorrow. I see in the wiring diagrams to use a X + and an X - limit switchso same with the Y axis. Bridgeport only uses one switch for +and -.what do I do?
Thanks Keith.
Thanks Keith.
This post has been liked 0 time(s).