O01001
G90
G53
G20
M65
(Mark Holes)
N55 G0 X0.525 Y0.5231
M64
A new report is attached.
Marking error
-
landmark573
- Posts: 96
- Joined: Mon Jun 24, 2019 3:30 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Marking error
I am getting the following error when running a marking operation.
The program is just a simple marking cycle:
O01001
G90
G53
G20
M65
(Mark Holes)
N55 G0 X0.525 Y0.5231
M64
A new report is attached.
The program is just a simple marking cycle:
O01001
G90
G53
G20
M65
(Mark Holes)
N55 G0 X0.525 Y0.5231
M64
A new report is attached.
- Attachments
-
- report_3484E41BC6EB-0511226197_2025-02-09_16-59-57.zip
- (5.72 MiB) Downloaded 3 times
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Allin1Chris
- PLC Expert
- Posts: 233
- Joined: Wed Jul 31, 2019 12:53 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
Re: Marking error
This is a known issue with V5.22, and has been corrected in V5.24.
It only required a macro update, so attached is the V5.24 macro. Can replace the file in C:\cncm\system and should correct the issue for V5.22 as well.
It only required a macro update, so attached is the V5.24 macro. Can replace the file in C:\cncm\system and should correct the issue for V5.22 as well.
- Attachments
-
- marking_cycle_macro.cnc
- (1.96 KiB) Downloaded 2 times
When requesting support READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
Centroid PLC Tutorial Videos
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
Centroid PLC Tutorial Videos
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
landmark573
- Posts: 96
- Joined: Mon Jun 24, 2019 3:30 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Marking error
Thanks Chris. I decided to go ahead and upgrade to v5.24. I haven't been able to test it out yet due to the weather.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)