Hello
I`m very new to centroid and I`m very confused if i have to connect my HBS860H drive to DB25 breakout or can i go straight to the screw terminals.
Has anybody wired this spefic controller?
I have seen 3 posts and Franco videos and still don`t have the answer.
I read the stepper documentation and it`s saying 5-24v signal, however on page 94 of centroid manual it states that "In Most, use DB25 step and direction.
My steppers are powered with 48v dc nema 34
Any advise is greatly appreciated.
Kris
HBS860H to DB25 OR Screw terminals?
Moderator: cnckeith
-
mOSkit
- Posts: 2
- Joined: Sat Jul 19, 2025 4:46 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
HBS860H to DB25 OR Screw terminals?
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
tblough
- Community Expert
- Posts: 3539
- Joined: Tue Mar 22, 2016 10:03 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Boston, MA
- Contact:
Re: HBS860H to DB25 OR Screw terminals?
Steppers are wired to the DB25.
Cheers,
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
mOSkit
- Posts: 2
- Joined: Sat Jul 19, 2025 4:46 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: HBS860H to DB25 OR Screw terminals?
So, why on Franco videos I see him wired into the screw terminals?
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
suntravel
- Community Expert
- Posts: 3628
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: HBS860H to DB25 OR Screw terminals?
Because with some stepper drives it is working also, but not as smooth as on DB25.
Uwe
(Note: Liking will "up vote" a post in the search results helping others find good information faster)