Search found 7459 matches
- Thu May 16, 2024 6:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help <DYN4 as spindle motor>
- Replies: 35
- Views: 866
- Thu May 16, 2024 6:44 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help <DYN4 as spindle motor>
- Replies: 35
- Views: 866
Re: Analog Out weirdness, please help <DYN4 as spindle motor>
links to look at https://centroidcncforum.com/viewtopic.php?p=62006#p62006 https://centroidcncforum.com/viewtopic.php?p=62126#p62126 looks like you read this one! https://centroidcncforum.com/viewtopic.php?p=62129#p62129 where gary says I tried using DMM a few years back, but like most here the resu...
- Thu May 16, 2024 6:42 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help <DYN4 as spindle motor>
- Replies: 35
- Views: 866
Re: Analog Out weirdness, please help <DYN4 as spindle motor>
Gary says "I use LeadShine EM motors with ELP drives to drive the spindles on small wood lathes that I produce. I use them in both velocity (-10-0-10 volt) mode AND step and direction mode, switched by an input."
- Thu May 16, 2024 6:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help <DYN4 as spindle motor>
- Replies: 35
- Views: 866
Re: Analog Out weirdness, please help <DYN4 as spindle motor>
this forum is a place for users to share their experience and information searching that info would be a good place to start your research before buying a component and going all lone ranger. this "dyn4 as spindle motor" comes up about every six months or so, i personally don't know anyone...
- Thu May 16, 2024 6:13 pm
- Forum: Centroid Hickory CNC Controller
- Topic: 9045 Z axis fault
- Replies: 2
- Views: 147
Re: 9045 Z axis fault
hello.
please follow the tech support request posting guidelines and provide detailecd information about your machine/project
starting by posting a fresh report.zip
please follow the tech support request posting guidelines and provide detailecd information about your machine/project
starting by posting a fresh report.zip
- Thu May 16, 2024 6:10 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help <DYN4 as spindle motor>
- Replies: 35
- Views: 866
Re: Analog Out weirdness, please help <DYN4 as spindle motor>
i think others have tired with the DYN4 as spindle motor and gave up and went with other solutions that have been proven to work.
- Thu May 16, 2024 3:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rough Motion on Circular Toolpaths
- Replies: 51
- Views: 1271
Re: Rough Motion on Circular Toolpaths
need much more info to help you, this is machine related, either mechanical or motor resolution (electronic or mechanical or both)
please read the tech support request posting guidelines.
need photos of the machine, lots of them.
and a fresh report.zip
otherwise we are all just guessing.
please read the tech support request posting guidelines.
need photos of the machine, lots of them.
and a fresh report.zip
otherwise we are all just guessing.
- Wed May 15, 2024 2:13 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Axis motion after electronics moved to new enclosure
- Replies: 20
- Views: 672
Re: Axis motion after electronics moved to new enclosure
The machine has a Left Y axes and a Right Y axes that are paired. When I push Y- on the VCP, the right and left Y axis moves in the correct direction (Y-) together. When I push Y+ on the VCP, the right axis moves in the correct direction (Y+) but the left moves in the Y- direction. The X and Z axis...
- Wed May 15, 2024 2:11 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Introduction video to using Notepad ++ and the NCnetic G code editing plugin.
- Replies: 9
- Views: 406
Re: Introduction video to using Notepad ++ and the NCnetic G code editing plugin.
Hi, There is a problem with the 1.30 PC Tuner installing the NCnetic plugin for Notepad++. The PC Tuner only looks for a Notepad++ installation on the C: drive. If Notepad++ is installed on a different drive, the PC Tuner is unable to located the installation. Otherwise the NCnetic plugin is very n...
- Wed May 15, 2024 1:55 pm
- Forum: Machining Strategies. Work Holding, Tool Path, Cutters, Feeds/Speeds etc.
- Topic: Dxf
- Replies: 74
- Views: 39501
Re: Dxf
no. you can use the cad system to break up the poly radius arcs into either 1.) small lines, 2.) real arcs. if you want to use Intercon. otherwise use a CAD/CAM system. i would recommend Vectric Cut 2D for this kind of work, it is similar to Intercon in many regards but, is CAD based and will accept...