Page 6 of 9
Re: Chinese hsd spindle
Posted: Wed Apr 29, 2020 9:26 am
by martyscncgarage
Rosmadi wrote: ↑Wed Apr 29, 2020 8:06 am
martyscncgarage wrote: ↑Mon Apr 27, 2020 11:58 pm
I would recommend dry contact relay outputs.
Founded this, ali baba,
Is this suitable,
Instead of providing screenshots, provide links.....
PIcture doesn't do much good without being able to read the specs/info
Re: Chinese hsd spindle
Posted: Mon May 04, 2020 12:55 am
by Rosmadi
martyscncgarage wrote: ↑Wed Apr 29, 2020 9:26 am
Rosmadi wrote: ↑Wed Apr 29, 2020 8:06 am
martyscncgarage wrote: ↑Mon Apr 27, 2020 11:58 pm
I would recommend dry contact relay outputs.
Founded this, ali baba,
Is this suitable,
Instead of providing screenshots, provide links.....
PIcture doesn't do much good without being able to read the specs/info
Here
https://m.alibaba.com/product/606273081 ... hare%22%7D
Re: Chinese hsd spindle
Posted: Mon May 04, 2020 9:27 am
by martyscncgarage
Looks right because it shows the inputs with a negative number but you'd better contact them to make sure its NPN
Re: Chinese hsd spindle
Posted: Wed May 06, 2020 11:00 am
by Rosmadi
martyscncgarage wrote: ↑Mon May 04, 2020 9:27 am
Looks right because it shows the inputs with a negative number but you'd better contact them to make sure its NPN
Thanks marty,, contact has been made, NPN is confirmed,
Re: Chinese hsd spindle
Posted: Fri May 15, 2020 12:39 pm
by Rosmadi
Hi marty, got the relay board,, which schematic should i follow
Re: Chinese hsd spindle
Posted: Fri May 15, 2020 1:52 pm
by martyscncgarage
Do you have basic electrical/electronic skills?
Very important to be successful and to be able to work your way through the conversion.
Use the Generic VFD wiring as a guide.
You will connect 24VDC from Acorn logic power supply to the COM terminal of that relay board.
You have 8 relays. The older revision Acorn board has two relays on it.
You will take Outputs 3-8 on Acorn to Inputs 3-8 on the relay board.
Marty
Re: Chinese hsd spindle
Posted: Sat May 16, 2020 1:57 pm
by Rosmadi
martyscncgarage wrote: ↑Fri May 15, 2020 1:52 pm
Do you have basic electrical/electronic skills?
Very important to be successful and to be able to work your way through the conversion.
Use the Generic VFD wiring as a guide.
You will connect 24VDC from Acorn logic power supply to the COM terminal of that relay board.
You have 8 relays. The older revision Acorn board has two relays on it.
You will take Outputs 3-8 on Acorn to Inputs 3-8 on the relay board.
Marty
ok, i guess i have to try it outn
Re: Chinese hsd spindle
Posted: Sun Jun 07, 2020 10:04 am
by Rosmadi
Hi, my output 4 for spindle foward is seem not respone,, can i use output 3 for spindle foward, and how to repair output4 if is damage,, i think i use those ouput4 to power some relay at the first place ,, maybe i made a wrong connection,,
Re: Chinese hsd spindle
Posted: Sun Jun 07, 2020 10:05 am
by martyscncgarage
Rosmadi wrote: ↑Sun Jun 07, 2020 10:04 am
Hi, my output 4 for spindle foward is seem not respone,, can i use output 3 for spindle foward, and how to repair output4 if is damage,, i think i use those ouput4 to power some relay at the first place ,, maybe i made a wrong connection,,
ALWAYS post a fresh report when asking for help Rosmadi.
Please post pictures of how you wired up the relay.
Post a screen shot of your Wizard input and output screens.
You need to make sure you wired that relay board correctly FIRST.
Re: Chinese hsd spindle
Posted: Mon Jun 08, 2020 2:46 am
by Rosmadi
sorry, here myreport. picture is on the way.. i have use my phone to post it,,is easy that way