Page 2 of 2
Re: Huan Yang VFD/Spindle not spinning (Resolved)
Posted: Mon Mar 08, 2021 11:17 am
by martyscncgarage
sahtijan wrote: ↑Sat Mar 06, 2021 10:49 pm
Can You please post your finaly picture of your vfd.
Did you jump form (under) DCM to FOR and did you make jumper from P + to PR?
This post give me so much information beacuse I have to wire my vfd.
Which HY VFD do you have? HY or GT?
Attached are my notes, they may help you get started.
Marty
Re: Huan Yang VFD/Spindle not spinning (Resolved)
Posted: Sat Apr 17, 2021 6:10 pm
by sahtijan
martyscncgarage wrote: ↑Mon Mar 08, 2021 11:17 am
sahtijan wrote: ↑Sat Mar 06, 2021 10:49 pm
Can You please post your finaly picture of your vfd.
Did you jump form (under) DCM to FOR and did you make jumper from P + to PR?
This post give me so much information beacuse I have to wire my vfd.
Which HY VFD do you have? HY or GT?
Attached are my notes, they may help you get started.
Marty
Hellou Marty. I have folow all your instruction on this forum and YouTube and everything works perfect. Today I have made my fist piece. Everything works so good.
But I have one little problem.
When I recall g code, same tool, same G54, same g code, same piece, my WCS G54 moves a litlle bit in negative direction,(all 3 axis) .I use Acorn Pro a it is router without atc.
Do you know what can be problem.
Re: Huan Yang VFD/Spindle not spinning (Resolved)
Posted: Sat Apr 17, 2021 6:13 pm
by sahtijan
And where is best place on this forum to post my succes story with pics. I built my first cnc
router and what Centroid do with you and their peolpe it is simple amazing.
It is My fist "problem" that I have.
Re: Huan Yang VFD/Spindle not spinning (Resolved)
Posted: Sat Apr 17, 2021 6:23 pm
by martyscncgarage
sahtijan wrote: ↑Sat Apr 17, 2021 6:10 pm
martyscncgarage wrote: ↑Mon Mar 08, 2021 11:17 am
sahtijan wrote: ↑Sat Mar 06, 2021 10:49 pm
Can You please post your finaly picture of your vfd.
Did you jump form (under) DCM to FOR and did you make jumper from P + to PR?
This post give me so much information beacuse I have to wire my vfd.
Which HY VFD do you have? HY or GT?
Attached are my notes, they may help you get started.
Marty
Hellou Marty. I have folow all your instruction on this forum and YouTube and everything works perfect. Today I have made my fist piece. Everything works so good.
But I have one little problem.
When I recall g code, same tool, same G54, same g code, same piece, my WCS G54 moves a litlle bit in negative direction,(all 3 axis) .I use Acorn Pro a it is router without atc.
Do you know what can be problem.
You need to start your own NEW TOPIC
Please follow this post and provide the information requested, especially provide a fresh Report
http://centroidcncforum.com/viewtopic.php?f=20&t=383
Re: Huan Yang VFD/Spindle not spinning (Resolved)
Posted: Sat Apr 17, 2021 6:25 pm
by martyscncgarage
sahtijan wrote: ↑Sat Apr 17, 2021 6:13 pm
And where is best place on this forum to post my succes story with pics. I built my first cnc
router and what Centroid do with you and their peolpe it is simple amazing.
It is My fist "problem" that I have.
In the Success Stories Forum:
viewforum.php?f=20
Thank you for sharing you project with everyone!