Allin1DC VFD wiring
Moderator: cnckeith
-
routebot
- Posts: 53
- Joined: Wed Aug 08, 2018 9:47 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: Yes
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Allin1DC VFD wiring
Im working on a knee mill CNC conversion. I connected the some of the wires but, I'm not sure about the rest. The VFD doesn't use the same labels as Centroid. Looking for clarity. Thanks!
- Attachments
-
-
-
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Centroid_Tech2
- Posts: 118
- Joined: Mon Mar 03, 2014 4:24 pm
- Allin1DC CNC Controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
Re: Allin1DC VFD wiring
These connection points called out are for the OAK board, but the wire numbers and colors will match.
When requesting support READ THIS POST first. viewtopic.php?f=60&t=1043
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
1 user liked this post
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
routebot
- Posts: 53
- Joined: Wed Aug 08, 2018 9:47 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: Yes
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Allin1DC VFD wiring
Thanks for the correct wiring diagram. I assume the remaining 5 wires are not used. Correct?
- Attachments
-
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
Re: Allin1DC VFD wiring
Optionally, you could jumper YEL from R1 to DOC, then connect WHT/BRN from DO3 to INP12 on the Allin1DC.
That would give you a "spindle zero speed" signal, which can be useful in some situations.
However, on a knee mill with no PLC control of the drawbar and with no automated gear shifting, you probably don't need it.
That would give you a "spindle zero speed" signal, which can be useful in some situations.
However, on a knee mill with no PLC control of the drawbar and with no automated gear shifting, you probably don't need it.
1 user liked this post
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
(Note: Liking will "up vote" a post in the search results helping others find good information faster)