Pat,
Glad to hear you got everything working. I have the same kit with 3 axis for a mini mill conversion. Your post helped me get to a successful setup and bench test of one motor.
I do have a question about how you have the "brake" terminal on the driver. It appears to be a purple wire. Is it hooked to a relay setup?
Bob
Stepperonline wiring for CL57T drive to ACORN CNC controller
Moderator: cnckeith
-
- Posts: 1
- Joined: Sun Dec 22, 2024 8:38 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 8648
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Stepperonline wiring for CL57T drive to ACORN CNC controller
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 8
- Joined: Wed Jul 10, 2024 11:00 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: E06234471BD4-0328248149
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Minnesota
Re: Stepperonline wiring for CL57T drive to ACORN CNC controller
Hi Bob,Bob.m1776 wrote: ↑Sun Dec 22, 2024 6:12 pm Pat,
Glad to hear you got everything working. I have the same kit with 3 axis for a mini mill conversion. Your post helped me get to a successful setup and bench test of one motor.
I do have a question about how you have the "brake" terminal on the driver. It appears to be a purple wire. Is it hooked to a relay setup?
Bob
I don't have a brake set up for any motors. The purple wire is my enable signal that goes back to Input 5 (IN5) on Acorn controller.
Pat
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 117
- Joined: Tue Aug 14, 2018 10:49 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: noneC120192
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
- Location: Denver, CO
Re: Stepperonline wiring for CL57T drive to ACORN CNC controller
Is this covered in a different thread?
Otherwise, FYI
Gary
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Community Expert
- Posts: 3611
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Stepperonline wiring for CL57T drive to ACORN CNC controller
In the manual of the driver....
Uwe
Uwe
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Community Expert
- Posts: 3015
- Joined: Fri May 24, 2019 8:34 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7804734C6498-0401191832
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Clearwater, FL
Re: Stepperonline wiring for CL57T drive to ACORN CNC controller
The COM is the common negative for the alarm and brake. This is all outlined in the manual.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Community Expert
- Posts: 3611
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Stepperonline wiring for CL57T drive to ACORN CNC controller
Jep, and to change from NO to NC use the software for the driver....
Uwe
Uwe
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 733
- Joined: Thu Feb 08, 2018 7:57 am
- Acorn CNC Controller: No
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Stepperonline wiring for CL57T drive to ACORN CNC controller
I'm looking for 'decent' stepper drivers for the 4 axis granite machine im retrofitting. Would these be recommended? Only 2 in stock in the UK but can order elsewhere if needed.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)