Hey All -
I think I'm going crazy - I can't get my Y axis to show any changes when I save distance travel adjustments. The data will save and write to the adjustments screen but with the actual movement of the axis nothing changes, it keep repeating the error. The X axis works fine and I was able to make all the corrections I needed but the Y axis wont actually save my changes.
I have enabled screw comp in the motor config screen and I have done the standard process. (thinking about this after I wrote everything - I wonder if the file doesnt say "Y" but the screen does and that is causing my issues - will check tomorrow)
I dont have any images today but I may get some tomorrow.
Also at one point I did have an issue with travel limits not matching - I dont remember if it was for Y or X. I went into the CNC-__.tab file and removed all the extra travel I didnt need.
I have a feeling this issue is caused by some backend file not being correct - but IDK
any thoughts ?
Screw Comp Not Working / Saving (Comp is enabled)
Moderator: cnckeith
-
- Posts: 10
- Joined: Thu Dec 30, 2021 3:14 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Screw Comp Not Working / Saving (Comp is enabled)
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 8031
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Screw Comp Not Working / Saving (Comp is enabled)
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 10
- Joined: Thu Dec 30, 2021 3:14 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Screw Comp Not Working / Saving (Comp is enabled)
I have a video uploading to youtube right now that I'll put the link here once its complete - but what I have found is that if I put the correction value in the next row down it'll work .... as in
if you are working on 0.0 > 0.5 instead of putting the variance in the row for 0.5 put it in 1 and it will impact 0.5.
The video has 1 hour ish remaining
if you are working on 0.0 > 0.5 instead of putting the variance in the row for 0.5 put it in 1 and it will impact 0.5.
The video has 1 hour ish remaining
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 8031
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Screw Comp Not Working / Saving (Comp is enabled)
post a fresh report.zip
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 10
- Joined: Thu Dec 30, 2021 3:14 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Screw Comp Not Working / Saving (Comp is enabled)
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 8031
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Screw Comp Not Working / Saving (Comp is enabled)
thanks for posting the video, i'll take a look at the video later today, in the meantime please post a report.zip so we can see and use your setup.
how much backlash does this machine have on each axis?
have you seen uwe's and alan's setup / test videos? on this thread
https://centroidcncforum.com/viewtopic. ... omp#p80095
how much backlash does this machine have on each axis?
have you seen uwe's and alan's setup / test videos? on this thread
https://centroidcncforum.com/viewtopic. ... omp#p80095
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 10
- Joined: Thu Dec 30, 2021 3:14 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Screw Comp Not Working / Saving (Comp is enabled)
the backlash isnt great - I am using lead screws vs ball screws - but I dont think hardware is my issue - as the software fields are not responding only for one axis.cnckeith wrote: ↑Thu Mar 14, 2024 2:22 pm thanks for posting the video, i'll take a look at the video later today, in the meantime please post a report.zip so we can see and use your setup.
how much backlash does this machine have on each axis?
have you seen uwe's and alan's setup / test videos? on this thread
https://centroidcncforum.com/viewtopic. ... omp#p80095
see my report attached
But overall i have sorta moved on by just shifting down my compensation to the next interval and it will change the prior interval ( hopefully the video makes sense )
Yeah i watched all the vids on how to do this - my x axis is complete its more of why do i have to put my 0 to 0.5 compensation in the 1.5in section to get it to impact the .5 compensation. everything is shifted down one rown to have an impact on the row above
- Attachments
-
- report_0035FF93AD4F-0421214690_2024-03-14_17-29-32.zip
- (704.63 KiB) Not downloaded yet
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 8031
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Screw Comp Not Working / Saving (Comp is enabled)
ok thanks for the report, we'll investigate.
leadscrews..ugh...time to put some cnc ballscrews in that machine!
leadscrews..ugh...time to put some cnc ballscrews in that machine!
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
(Note: Liking will "up vote" a post in the search results helping others find good information faster)