Depends on the CAM. You can have a complete machine model to do simulations, detect possible crash...
Very handy for multiaxis mill turn machines.
Uwe
Cnc12 V5.06 loading a program
Moderator: cnckeith
-
suntravel
- Posts: 2720
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Cnc12 V5.06 loading a program
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Sword
- Posts: 742
- Joined: Fri Nov 30, 2018 1:04 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Thorp WI
Re: Cnc12 V5.06 loading a program
It sounds like you may be asking about the G-code preview when a file is loaded.
In the Wizard...Preferences/CNC Control, and set "Part G-Code Preview On Job Load" to "Yes".
In the Wizard...Preferences/CNC Control, and set "Part G-Code Preview On Job Load" to "Yes".
Scott
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Houseman303
- Posts: 150
- Joined: Sun Nov 12, 2023 1:33 pm
- Acorn CNC Controller: No
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: Yes
- CNC Control System Serial Number: A901313
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Switzerland
Re: Cnc12 V5.06 loading a program
wizard only for acorn acorn/6
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
suntravel
- Posts: 2720
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Cnc12 V5.06 loading a program
But manual is the same on all
Look at parameter 46
Uwe
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Houseman303
- Posts: 150
- Joined: Sun Nov 12, 2023 1:33 pm
- Acorn CNC Controller: No
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: Yes
- CNC Control System Serial Number: A901313
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Switzerland
Re: Cnc12 V5.06 loading a program
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
suntravel
- Posts: 2720
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Cnc12 V5.06 loading a program
ok, then P#417=1
Uwe
Uwe
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
cnckeith
- Posts: 8072
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Cnc12 V5.06 loading a program
post a fresh report.zip so we can see your configuration settings.
G code preview is a feature in CNC12 that is not on by default in some installations, to turn it on use P417 (part g code preview) as pointed out by Uwe (thanks)
other g code job related parameters are:
Display active g codes. P46
Run time graphics on by default P150 ( i set this to NO, as you can always go into the graphics mode at any point from the main screen)
Remember last g code job after restart P401
i'm moving this thread out of the beta forum since its not a beta discussion.
G code preview is a feature in CNC12 that is not on by default in some installations, to turn it on use P417 (part g code preview) as pointed out by Uwe (thanks)
other g code job related parameters are:
Display active g codes. P46
Run time graphics on by default P150 ( i set this to NO, as you can always go into the graphics mode at any point from the main screen)
Remember last g code job after restart P401
i'm moving this thread out of the beta forum since its not a beta discussion.
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
(Note: Liking will "up vote" a post in the search results helping others find good information faster)