I am getting an MPG encoder error, but everything seems to work fine.
Also have a program that will not run "Abnormal End of Job"?
Checked other programs and they have the same end to the program.
Attached program 3333 is the one that gives error and 3336 runs fine.
These are both engraving programs and almost identical program.
I deleted the middle part of each program to reduce file size
Error Codes 417 & 421
Moderator: cnckeith
-
- Posts: 59
- Joined: Tue Apr 10, 2018 9:36 am
- Acorn CNC Controller: No
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: Yes
- CPU10 or CPU7: Yes
Error Codes 417 & 421
- Attachments
-
- report_0121130653_2022-12-17_15-56-16.zip
- (7.4 MiB) Downloaded 1 time
-
- 3333.txt
- (438 Bytes) Downloaded 4 times
-
- 3336.txt
- (460 Bytes) Downloaded 5 times
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
Re: Error Codes 417 & 421
"Abnormal end of job" does not mean that the G codes at the end of your CNC file were abnormal.
Instead, it means that the job stopped running for some reason that CNC12 did not have a better description for.
Instead, it means that the job stopped running for some reason that CNC12 did not have a better description for.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 59
- Joined: Tue Apr 10, 2018 9:36 am
- Acorn CNC Controller: No
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: Yes
- CPU10 or CPU7: Yes
Re: Error Codes 417 & 421
Ok
Then it could be in the middle of the program?
Will not run graph either
Then it could be in the middle of the program?
Will not run graph either
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 3274
- Joined: Tue Mar 22, 2016 10:03 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Boston, MA
- Contact:
Re: Error Codes 417 & 421
3333.txt is a subprogram. My guess is the error is because you are trying to run a subprogram without an M99 return from subprogram. Programs names starting with an O and followed with a number in the range of 9100-9999 are subprograms. Refer to pg. 253 in the 4.22 mill operator's manual.
Cheers,
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 59
- Joined: Tue Apr 10, 2018 9:36 am
- Acorn CNC Controller: No
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: Yes
- CPU10 or CPU7: Yes
Re: Error Codes 417 & 421
Ok Thanks
That makes sense
I will try changing the number
O's are in most of my programs because my Fanuc controls require it
That makes sense
I will try changing the number
O's are in most of my programs because my Fanuc controls require it
(Note: Liking will "up vote" a post in the search results helping others find good information faster)