Flyback Diode Necessity

All things related to the Centroid Acorn CNC Controller

Moderator: cnckeith

Post Reply
RJS100
Posts: 380
Joined: Tue Oct 20, 2020 8:41 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Arizona

Flyback Diode Necessity

Post by RJS100 »

I read that if the output relays on the Acorn board are used to control a direct current solenoid valve (for example to turn on mist coolant) then it is good practice to wire a flyback diode across the coils of the solenoid valve. This is said to prevent voltage spikes created when power to the solenoid valve is shut off.

I currently use an Acorn output to turn on a 12 V DC mill light. I would like to add a 120 V AC enclosure light that will turn on with the mill light. To avoid using another output relay on the Acorn board, I installed a small SPST relay with a 12 VDC coil. This allows me to turn on the 120 V AC lights when the 12-volt mill light is turned on.

Do I need to wire a Flyback diode across the coil of this SPST relay to prevent voltage spikes from damaging the Acorn output relays?
Are Flyback diodes necessary to protect the output relays on the Acorn board?

Thanks... Richard
rk9268vc
Posts: 267
Joined: Fri Nov 13, 2020 4:12 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Flyback Diode Necessity

Post by rk9268vc »

Use a solenoid with a built in relay, dont power the coils directly.

example:


This way all Acorn is doing is powering a relay. No flyback diode needed.

"Do I need to wire a Flyback diode across the coil of this SPST relay"
no
ShawnM
Posts: 2190
Joined: Fri May 24, 2019 8:34 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 7804734C6498-0401191832
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Clearwater, FL

Re: Flyback Diode Necessity

Post by ShawnM »

I would add a diode to any DC relay and a snubber circuit to any AC relay coil or contactor. It's just cheap insurance.
Gary Campbell
Posts: 2164
Joined: Sat Nov 18, 2017 2:32 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: Acorn 238
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Marquette, MI
Contact:

Re: Flyback Diode Necessity

Post by Gary Campbell »

If I were going to power a low power 120vac device I would use a solid state relay, which are made for that exact task
GCnC Control
CNC Control & Retrofits
https://www.youtube.com/user/Islaww1/videos
RJS100
Posts: 380
Joined: Tue Oct 20, 2020 8:41 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Arizona

Re: Flyback Diode Necessity

Post by RJS100 »

Thanks for your thoughts. Very much appreciated. The solenoid shown is exactly what I have been using. I have been directed to use snubbers and flyback diodes exactly as Shawn has noted.

The idea of a solid-state relay is also something I never thought of. No coil, no inductance... No voltage spike.

Thanks.
Upnorth
Posts: 237
Joined: Wed Apr 01, 2020 8:23 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 1702
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Flyback Diode Necessity

Post by Upnorth »

How reliable are the solid state relays?
Richards
Posts: 692
Joined: Sun Sep 16, 2018 9:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: South Jordan, UT

Re: Flyback Diode Necessity

Post by Richards »

Solid State Relays are dependable. I've used hundreds of them in photo printers without a failure. They do have one drawback which is that some of them allow leakage voltage when they are turned off. A normal mechanical relay completely opens the circuit when OFF An SSR doesn't always totally shut off, depending on the SSR type and its load. The lighter the load, the more apt the SSR is to have some leakage. The leakage seems to be more common in SSRs that turn ON/OFF using a zero-voltage detection circuit. It's not something to worry about, but you need to be aware that there might be a shock hazard when you would assume that the power is off.
-Mike Richards
suntravel
Posts: 1967
Joined: Thu Sep 23, 2021 3:49 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 6433DB0446C1-08115074
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Germany

Re: Flyback Diode Necessity

Post by suntravel »

On the production machines we change all small relays to SSR, because they are extreme reliable. I did not know about a fail the last 20 years.

Voltage leak is there make it irritating to check with some Multimeters if they are off.

Uwe
Post Reply