Hi all, I was curious if I can change smoothing modes with a command in a G Code file. I took a look at the docs and I didn't see anything in there about it...
Is this possible? Has anyone ever done it? If so I'd be interested in knowing how...
Change smoothing via command?
Moderator: cnckeith
-
- Posts: 373
- Joined: Fri Jan 10, 2014 11:29 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Howard, PA
Re: Change smoothing via command?
I haven't done it, but it should be possible. Check into G10 to write parameters and parameters 220-231.
-
- Posts: 148
- Joined: Wed Jan 01, 2020 2:40 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Change smoothing via command?
I have different PP set up for each smoothing profile for Vectric. If you look at the acorn smoothing users manual it explains it a little further.
G64 is the command to turn smoothing on/off, see page 221 of the users manual.
G64 is the command to turn smoothing on/off, see page 221 of the users manual.
-
- Posts: 667
- Joined: Fri Nov 30, 2018 1:04 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Thorp WI
Re: Change smoothing via command?
Same here as RogDC. One PP for standard "precision router", one for 3D relief, and one for V-carving. Each reverts to my standard "precision router" when done.
Example... G64 ON "3D Relief Fine" ; Activate desired preset by label
Example... G64 ON "3D Relief Fine" ; Activate desired preset by label
Scott
-
- Posts: 7334
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Change smoothing via command?
look up G64 in the mill operator manual (page 222) and the corresponding 'smoothing' menu section (page 336) of same manual.
the mill operator manual is found in the "All Acorn Documentation" thread here.
viewtopic.php?f=60&t=3397
the mill operator manual is found in the "All Acorn Documentation" thread here.
viewtopic.php?f=60&t=3397
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 199
- Joined: Mon Oct 29, 2018 5:25 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Change smoothing via command?
That's great advice everyone. I really appreciate it.