Error in Allinone dc control installation manual

All things related to Centroid Oak, Allin1DC, MPU11 and Legacy products

Moderator: cnckeith

Post Reply
cncot
Posts: 57
Joined: Wed Jan 06, 2021 1:05 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: console 104030 SysId 0008DC111213-1202202505
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Mims Florida

Error in Allinone dc control installation manual

Post by cncot »

Gentlemen,
I noticed a minor error in your Allinone dc control installation manual page 15 concerning the limit switch defeat. I thought you would like to know. Please correct line 2 it reads funny and one pushes the switches down to defeat. I almost fell into the trap of up! Had I persisted, I would have broken the DIP switch!
I just powered up my Allin1 for the first time a few minutes ago. Wish me well please. I have been working on this since Christmas almost every day, drawing my custom schematics based on yours, ordering parts and wiring. Any needed support will be welcomed. I am ready to get this done an over...
Warm Regards
Mike
tblough
Posts: 3071
Joined: Tue Mar 22, 2016 10:03 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Boston, MA
Contact:

Re: Error in Allinone dc control installation manual

Post by tblough »

You are not using the latest version of the install manual. https://www.centroidcnc.com/centroid_di ... nuals.html
pg16 wrote:Move the limit switched from the down position to the up position
if the switch is black and from the up position to the down position if the switch is blue.
pg45 wrote:The limit switch defeaters (SW4) on the ALLIN1DC need to be pointed DOWN if SW4 is black and UP if SW4 is blue to be
able to use the limit switches.
Cheers,

Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
polaraligned
Posts: 231
Joined: Mon Feb 07, 2011 8:03 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 1030090103
DC3IOB: Yes
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No
Location: Montvale, NJ

Re: Error in Allinone dc control installation manual

Post by polaraligned »

Just to be picky, there is a minor error on page 38 of the AllIn1DC installation manual. The chart refers to 240 VAC two phase input. It should say single phase. Two phase power (90 degree out of phase) is not used in our power distribution system.
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Error in Allinone dc control installation manual

Post by martyscncgarage »

cncot wrote: Fri Mar 19, 2021 12:37 pm Gentlemen,
I noticed a minor error in your Allinone dc control installation manual page 15 concerning the limit switch defeat. I thought you would like to know. Please correct line 2 it reads funny and one pushes the switches down to defeat. I almost fell into the trap of up! Had I persisted, I would have broken the DIP switch!
I just powered up my Allin1 for the first time a few minutes ago. Wish me well please. I have been working on this since Christmas almost every day, drawing my custom schematics based on yours, ordering parts and wiring. Any needed support will be welcomed. I am ready to get this done an over...
Warm Regards
Mike
Mike, do be sure to follow this post when asking for help viewtopic.php?f=20&t=383
Follow the latest installation manual as Tom suggested, hopefully you found my video series on an All in One DC installation on YouTube.

Continued luck with your project!
Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
Post Reply