Anyone's help would be greatly appreciated!
Here's the issue. I am trying to run this F360 program on my Acorn CNC12 Ver4.14.
I keep getting an "Abnormal Job End" after I load the program and then try to Run it. I have always used F360 with success until now. I have a subscription as well.
Here's what I've done to diagnose it so far so this is all I can tell you.
1: I have made a CAM program using INTERCON and that works fine
2: I have loaded previous Fusion 360 programs from the directory and they run as well.
3: I have gone into F360, post processed the same earlier project, but the NEW copy does not work! I look at them in Notepad and they are identical!
4: I have made a simple CAM in F360 thinking maybe my program was to intense for ACORN. That works.
So here we are. Acorn seems to work but there seems a varying degree of uncertainty around Fusion 360.
I have also reloaded the Centroid post processor from Autodesk.
If anyone can look at or load this program to see what result they get, anything would be appreciated. I know that sounds shady loading a program but Im at my wits end try to get this to work.
Thank you for any input in advance.
Doug
Please Help!! (Resolved)
Moderator: cnckeith
-
- Posts: 25
- Joined: Sun Sep 30, 2018 10:05 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Connecticut
Please Help!! (Resolved)
- Attachments
-
- John Spoke.nc
- (229.45 KiB) Downloaded 93 times
-
- report_38D2693C2D16-0727181089_2021-01-12_20-34-37.zip
- (273.32 KiB) Downloaded 104 times
-
- Posts: 3072
- Joined: Tue Mar 22, 2016 10:03 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Boston, MA
- Contact:
Re: Please Help!!
You're creating a subprogram by using a program number in the rsnge of 9100-9999 without ending it with subprogram return (M99). Read the manual entry for M98.
Cheers,
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
-
- Posts: 25
- Joined: Sun Sep 30, 2018 10:05 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Connecticut
Re: Please Help!!
ok, thats a start. Honestly I'm new to this so thank you so much. I'll read up on that.
-
- Posts: 25
- Joined: Sun Sep 30, 2018 10:05 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Connecticut
Re: Please Help!!
THAT DID IT!!
So much to learn. Thank you so much.
Really appreciate it.
So much to learn. Thank you so much.
Really appreciate it.