Geneva umbrella wiring

All things related to Centroid Oak, Allin1DC, MPU11 and Legacy products

Moderator: cnckeith

occustoms
Posts: 129
Joined: Sun Jan 27, 2019 3:51 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: Yes
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Geneva umbrella wiring

Post by occustoms »

I cant seem to find the default wiring for using a 1616 on oak of where they want the sensors to and motors wired too? I have a fadal geneva drive with 2 110v dc motors. one for slide and one for turret. searched and havent seen anything. also need it for the drawbar and solenoids for air etc.
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Geneva umbrella wiring

Post by martyscncgarage »

occustoms wrote: Sat Jan 02, 2021 3:45 am I cant seem to find the default wiring for using a 1616 on oak of where they want the sensors to and motors wired too? I have a fadal geneva drive with 2 110v dc motors. one for slide and one for turret. searched and havent seen anything. also need it for the drawbar and solenoids for air etc.
Take a look at the attached OAK Schematic.
See if helps. You have to use the Inputs and Outputs as outlined in the schematic in order to use the corresponding PLC.

Marty
Attachments
s14663.r1.pdf
(279.17 KiB) Downloaded 133 times
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
occustoms
Posts: 129
Joined: Sun Jan 27, 2019 3:51 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: Yes
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: Geneva umbrella wiring

Post by occustoms »

Awesome thank you!
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Geneva umbrella wiring

Post by martyscncgarage »

occustoms wrote: Sat Jan 02, 2021 3:29 pm Awesome thank you!
Hope it helps...
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
occustoms
Posts: 129
Joined: Sun Jan 27, 2019 3:51 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: Yes
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: Geneva umbrella wiring

Post by occustoms »

martyscncgarage wrote: Sat Jan 02, 2021 4:19 pm
occustoms wrote: Sat Jan 02, 2021 3:29 pm Awesome thank you!
Hope it helps...
It does, only thing i have that is not listed is the oreintation arm. i have a solenoid that activates an arm with a small bearing that locks the spindle pulley from moving like when a m19 is activated.

So will i have to just wire to output on 1616 and have some custom plc for that?

I also have a atc fault switch that if the tool doesnt release during pick up or put down on carousel, that switch is activated and e-stops machine. should i just put this in line with estop circuit? or is their a better way?
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Geneva umbrella wiring

Post by martyscncgarage »

Does your orient arm have a sensor to let the control know when it in?

Does your machine have sensors for drawbar release and drawbar lock?
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
occustoms
Posts: 129
Joined: Sun Jan 27, 2019 3:51 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: Yes
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: Geneva umbrella wiring

Post by occustoms »

martyscncgarage wrote: Sat Jan 02, 2021 7:36 pm Does your orient arm have a sensor to let the control know when it in?

Does your machine have sensors for drawbar release and drawbar lock?

No on orint arm, and no on the drawbar. (factory fadal dont have it)

i can add a simple sensor and bracket for drawbar, but cant for orint, atleast not very easily.

i also dont have a seperate home for carousel, only out or in.

Can i just jumper the 1616 with home and carousel out?
cncsnw
Posts: 3763
Joined: Wed Mar 24, 2010 5:48 pm

Re: Geneva umbrella wiring

Post by cncsnw »

What Centroid usually means by "carousel home" is a rotational position, to tell if it is at or near tool 1.

As a rule, even though it appears on Centroid's schematic, such a sensor is really unnecessary on a Centroid control because the software will keep track of the carousel position from day to day. There is no need to home the carousel on power-up.
occustoms
Posts: 129
Joined: Sun Jan 27, 2019 3:51 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: Yes
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: Geneva umbrella wiring

Post by occustoms »

cncsnw wrote: Sat Jan 02, 2021 8:21 pm What Centroid usually means by "carousel home" is a rotational position, to tell if it is at or near tool 1.

As a rule, even though it appears on Centroid's schematic, such a sensor is really unnecessary on a Centroid control because the software will keep track of the carousel position from day to day. There is no need to home the carousel on power-up.
thank you that clears up one part.

so do i need to add a sensor for clamped and unclamped?

also what about the orient complete?
occustoms
Posts: 129
Joined: Sun Jan 27, 2019 3:51 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: Yes
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: Geneva umbrella wiring

Post by occustoms »

Well im blind it does have orient spindle sensor. Still need to know about clamped and unclamped sensor being needed?
Post Reply