Tool touch height
Moderator: cnckeith
-
Dholman
- Posts: 52
- Joined: Mon Aug 06, 2018 11:44 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Tool touch height
Everytime I enter the height to be subtracted in the wizard and save and close the wizard it goes back to zero and does not subtract is there a specific order that needs saved
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
cnckeith
- Site Admin
- Posts: 8935
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Tool touch height
you'll have to post a fresh report.zip
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Dholman
- Posts: 52
- Joined: Mon Aug 06, 2018 11:44 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Tool touch height
here is my report
- Attachments
-
- report_780473845840-0206191632_2019-05-22_11-33-19.zip
- (315.44 KiB) Downloaded 115 times
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
cnckeith
- Site Admin
- Posts: 8935
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Tool touch height
ok...i confirm.. so as a work around.. go to cnc12 and set Parameter 71 to a negative value of the TT height device and it will stick..
then you don't have to worry about the wizard resetting to zero
then you don't have to worry about the wizard resetting to zero
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Dholman
- Posts: 52
- Joined: Mon Aug 06, 2018 11:44 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Tool touch height
That worked thank you
(Note: Liking will "up vote" a post in the search results helping others find good information faster)