ACORN Rev 4 Controller Board

Commotion · Post by **Commotion** » Wed Feb 20, 2019 10:29 pm

I bought the original one just before the rev3 came out. It works fine. I am borrowing a rev 3 board from a mate to get the lathe up and running but glad I have delayed buying another acorn so next one I buy can be a rev4... unless ur doing a stellar deal on old rev 3 stock Keith

.

EricMack · Post by **EricMack** » Wed Feb 20, 2019 11:05 pm

Gary, that looks like a useful testing board. I'm curious what the two rotary [switches?] are in the lower left, and how they work for your testing...

Gary Campbell · Post by **Gary Campbell** » Wed Feb 20, 2019 11:35 pm

Eric...
I use those switches to toggle the limits (IP 1-4) and tool measure (IP 5) from normally open to normally closed so that I can setup controllers to match the components that my customers have. That way I can have all the wizard settings to match, as close as possible, the customer's machine. This gives them, in most cases pretty close to a plug and play solution and allows them to spend their first few weeks learning how to run the software, not set it up.

EricMack · Post by **EricMack** » Wed Feb 20, 2019 11:51 pm

That's a smart idea, Gary

Wolfenstien · Post by **Wolfenstien** » Thu Feb 21, 2019 8:27 am

Looks like Rev 3 boards are on amazon from centroid for $275 free shipping. I'm not sure if the $25 price break it to sell off the old inventory or if you'd get a Rev 4 board when buying from amazon.

Post by **Centroid_Liviu** » Thu Feb 21, 2019 10:26 am

The discounted Acorns on Amazon are Rev 3. There are 8 left I think.

Post by **martyscncgarage** » Thu Feb 21, 2019 1:02 pm

I don't know of many that can say they have improved the hardware 4 times since the release of Acorn 18 months ago, and countless and continuing software upgrades and add ons.

This should speak volumes about Centroid listening to their customer base and their commitment to their motion control product line.

Marty

EricMack · Post by **EricMack** » Thu Feb 21, 2019 1:31 pm

Indeed. Very promising. Well done, Centroid Team

Post by **eng199** » Fri Feb 22, 2019 10:40 am

martyscncgarage wrote: ↑Thu Feb 21, 2019 1:02 pm I don't know of many that can say they have improved the hardware 4 times since the release of Acorn 18 months ago

Marty, your number is a bit low by my count. There have been 10 ACORN PCB versions, power supply upgrades, relay board, relay board adapter card...

Post by **martyscncgarage** » Fri Feb 22, 2019 10:45 am

eng199 wrote: ↑Fri Feb 22, 2019 10:40 am
martyscncgarage wrote: ↑Thu Feb 21, 2019 1:02 pm I don't know of many that can say they have improved the hardware 4 times since the release of Acorn 18 months ago
Marty, your number is a bit low by my count. There have been 10 ACORN PCB versions, power supply upgrades, relay board, relay board adapter card...

Matt...you are so picky...typical Engineer.

OKAY! Your point is well taken!
Have a good one, thank you for all the work you put into the hardware!
Marty

Centroid Community CNC Support Forum

ACORN Rev 4 Controller Board

Re: ACORN Rev 4 Controller Board

Re: ACORN Rev 4 Controller Board

Re: ACORN Rev 4 Controller Board

Re: ACORN Rev 4 Controller Board

Re: ACORN Rev 4 Controller Board

Re: ACORN Rev 4 Controller Board

Re: ACORN Rev 4 Controller Board

Re: ACORN Rev 4 Controller Board

Re: ACORN Rev 4 Controller Board

Re: ACORN Rev 4 Controller Board