I just ordered one of your nuk computers configured for use with my acorn plasma cutter. Is there an easy foolproof way to transfer all the configuration settings for my current computer to the new one.
Thanks
New computer question
-
cardin3
- Posts: 47
- Joined: Mon Nov 20, 2023 10:21 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: Yes
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7550
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
New computer question
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
tblough
- Community Expert
- Posts: 3518
- Joined: Tue Mar 22, 2016 10:03 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Boston, MA
- Contact:
Re: New computer question
If you are going from one version to the same, just copy /cnc? and all of its subdirectories. Then copy /intercon or /icn_lath depending what installation you are using. That will put you back where you left off.
If you are switching versions, then you'll need to follow the installation instructions.
If you are switching versions, then you'll need to follow the installation instructions.
Cheers,
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
cardin3
- Posts: 47
- Joined: Mon Nov 20, 2023 10:21 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: Yes
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7550
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: New computer question
I'm sure this new computer that I just received has the newest CNC plasma pro software on it I just want to configure it the same as my old software. As in Axis drives and all those settings.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Joey
- Plasma/Laser Lead
- Posts: 654
- Joined: Tue Aug 17, 2021 10:51 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: New computer question
You can select Ctrl-P in the wizard and create a PDF of the all the Wizard settings to reference.
The PC should have V5.3 installed. What version are you coming from?
The PC should have V5.3 installed. What version are you coming from?
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
cardin3
- Posts: 47
- Joined: Mon Nov 20, 2023 10:21 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: Yes
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7550
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: New computer question
I'm coming from 5.06 plasma pro
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Joey
- Plasma/Laser Lead
- Posts: 654
- Joined: Tue Aug 17, 2021 10:51 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: New computer question
It's worth updating to the 5.3 version of software.
Just snip each page of the Wizard or CTRL-P to create a PDF of your 5.06 Wizard settings and plug them into the new PC's CNC12 5.3 Wizard.
Just snip each page of the Wizard or CTRL-P to create a PDF of your 5.06 Wizard settings and plug them into the new PC's CNC12 5.3 Wizard.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)