Tool table in the report
Moderator: cnckeith
-
- Posts: 114
- Joined: Sun Nov 12, 2023 1:33 pm
- Acorn CNC Controller: No
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: Yes
- CNC Control System Serial Number: A901313
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Switzerland
Tool table in the report
Is it really necessary for the report to contain the tool table? Restoring an outdated tool table cost me a lot.
-
- Posts: 7439
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Tool table in the report
yes.
if you want to do something else. then copy/paste what you want into the cncm folder.
cncm.ol offset library
cncm.tl tool library
what are you using restore report to do?
if you want to do something else. then copy/paste what you want into the cncm folder.
cncm.ol offset library
cncm.tl tool library
what are you using restore report to do?
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 114
- Joined: Sun Nov 12, 2023 1:33 pm
- Acorn CNC Controller: No
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: Yes
- CNC Control System Serial Number: A901313
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Switzerland
Re: Tool table in the report
I had a PLC written with certain functions, unfortunately it produced the same inexplicable axis errors that I also got during my programming. Since I was supposed to import the report using the restore function, I did this with a working backup. Unfortunately, this backup was before the tool database was updated. Tool length 0 is not an advantage at rapid traverse of 1100 ipm. If the H length and D diameter of the currently active tool were displayed on the surface, this could be avoided. I know about Heidenhain control. It was also clearly visible there when G92 and/or G68 was active.
-
- Posts: 2106
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Tool table in the report
Make a backup of the PLC before changing it, so you can go back to the last working version.
Uwe
Uwe