I've got a new spindle mounted up and running.
This is new for me as I've spent the last 20 years using a Porter Cable 3-1/4 hp as my spindle.
Going through the centroid warm up the first thing it prompts is to remove the tool. My setup is not ATC by the way.
Is this prompt more for the ATC users, or should I be warming up without a tool in the collet?
Spindle warm up advice.
Moderator: cnckeith
-
robtown
- Posts: 124
- Joined: Mon Oct 15, 2018 10:13 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: F045DA78F172-1129181385
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
- Location: Atlanta GA
Spindle warm up advice.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Nigelo
- Posts: 415
- Joined: Tue Dec 11, 2018 4:03 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: F045DA80C8B8-0905181172
E415F6F70BC3-0318203049
98F07B91FC6B-0123236802 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: UK East Coast
Re: Spindle warm up advice.
For safety reasons I prefer to run without a tool installed but ALSO with collet nut removed
Hope this helps
Nigel
"You can lead a horse to water but you cannot force it to drink"
Nigel
"You can lead a horse to water but you cannot force it to drink"
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
suntravel
- Posts: 2895
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Spindle warm up advice.
This depends on the spindle, I would mine not run without a toolholder and a loose drawbar.
Uwe
Uwe
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Nigelo
- Posts: 415
- Joined: Tue Dec 11, 2018 4:03 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: F045DA80C8B8-0905181172
E415F6F70BC3-0318203049
98F07B91FC6B-0123236802 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: UK East Coast
Re: Spindle warm up advice.
Of course you are correct Uwe (as usual
) I should have stated that my router spindle has an ER25 collet chuck and not fixed toolholders i.e. no drawbar.
Hope this helps
Nigel
"You can lead a horse to water but you cannot force it to drink"
Nigel
"You can lead a horse to water but you cannot force it to drink"
(Note: Liking will "up vote" a post in the search results helping others find good information faster)