CNC lathe Dealing with long chips
Moderator: cnckeith
-
- Posts: 93
- Joined: Thu Sep 21, 2023 10:13 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: United Kingdom
CNC lathe Dealing with long chips
I had a job turning some parts made from 6082 T6 aluminium. The part was 90mm in diameter.
The problem was after about 3 passes 30mm long, the turnings would get caught in the chuck jaws and i would have to stop the program and remove the swarf then start where the program stopped.
I thought it would be a good idea to use a face grooving cycle in intercon.
I programmed the face grooving cycle to take a 1mm cut in X and peck cutting every 2mm in Z. It worked well breaking the chips every time it pecked.
The swarf was now manageable and no turnings ever got wrapped around the chuck again.
I also use the part off cycle for deep grooves as you can peck cut to produce perfect length chips.
I couldn't get the chips to break without any other method. It is not a big lathe and has limited capacity.
The problem was after about 3 passes 30mm long, the turnings would get caught in the chuck jaws and i would have to stop the program and remove the swarf then start where the program stopped.
I thought it would be a good idea to use a face grooving cycle in intercon.
I programmed the face grooving cycle to take a 1mm cut in X and peck cutting every 2mm in Z. It worked well breaking the chips every time it pecked.
The swarf was now manageable and no turnings ever got wrapped around the chuck again.
I also use the part off cycle for deep grooves as you can peck cut to produce perfect length chips.
I couldn't get the chips to break without any other method. It is not a big lathe and has limited capacity.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 8207
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: CNC lathe Dealing with long chips
thanks, i moved this post to the machining strategies forum.
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 3362
- Joined: Tue Mar 22, 2016 10:03 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Boston, MA
- Contact:
Re: CNC lathe Dealing with long chips
Increase the feedrate or the depth of cut to make chips break.
Cheers,
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 93
- Joined: Thu Sep 21, 2023 10:13 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: United Kingdom
Re: CNC lathe Dealing with long chips
I tried increasing the depth of cut to 2mm off the diameter but it just tears the chips but still doesn't break the chips.
I tried increasing the feedrate but it is still the same.
I just set the feedrate to what it reccomends on the carbide insert box. I am using ground inserts for aluminium.
On steel it will break chips.
I need a larger lathe.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 2868
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: CNC lathe Dealing with long chips
Sometimes pecking is the best solution for chip control, on large lathes also.
Uwe
Uwe
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 81
- Joined: Sat Jan 21, 2023 6:20 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 0008DC111213-1005220061
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: CNC lathe Dealing with long chips
hi, i am really new to intercon and i am wondering how can i use pecking for outer contour ?
Thanks
Michael
Thanks
Michael
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 2868
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: CNC lathe Dealing with long chips
No function other than cut off cycle for this in Intercon.
For OD turning, hand code, or write a function with a sub program.
The easiest way is to use AW2007 or AW2011 instead of 6082
Uwe
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 81
- Joined: Sat Jan 21, 2023 6:20 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 0008DC111213-1005220061
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: CNC lathe Dealing with long chips
hi Uwe,
thank you. for Aluminium i dont have an issue, 7075 is producing nice short chips with f0,2 and 100vc.
i am more talking about titanium, it is very hard here to get short chips.
thank you. for Aluminium i dont have an issue, 7075 is producing nice short chips with f0,2 and 100vc.
i am more talking about titanium, it is very hard here to get short chips.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 2868
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: CNC lathe Dealing with long chips
jep 7075 is easy to cut, but if it is possible from spindle speed, I use 200m/min or faster.
No problem to write a chip breaking function with parameters for roughing, but for finish cut it looks better in one go with one long swarf.
The trick here ist to make it flow away from the part so it will not scratch the surface.
Uwe
No problem to write a chip breaking function with parameters for roughing, but for finish cut it looks better in one go with one long swarf.
The trick here ist to make it flow away from the part so it will not scratch the surface.
Uwe
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
- Posts: 81
- Joined: Sat Jan 21, 2023 6:20 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 0008DC111213-1005220061
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: CNC lathe Dealing with long chips
hi Uwe,
yes, 200m would be better, but i have often Diameters of 20mm or smaller, so the spindle would be always in Max Speed. So i try to find good parameters with lower Vc.
pecking macro for outer roughing is a good idea, but at first i have to get confident with Intercon itself.
the last cut is not the problem, the ap is small, so no thick swarf, not that dangerous. but i am looking for a solution for roughing and good process parameters for the boring bars.
Michael
yes, 200m would be better, but i have often Diameters of 20mm or smaller, so the spindle would be always in Max Speed. So i try to find good parameters with lower Vc.
pecking macro for outer roughing is a good idea, but at first i have to get confident with Intercon itself.
the last cut is not the problem, the ap is small, so no thick swarf, not that dangerous. but i am looking for a solution for roughing and good process parameters for the boring bars.
Michael
(Note: Liking will "up vote" a post in the search results helping others find good information faster)