I have a Toshiba VFS7-2037P
Wired as suggested in a recent post.
OUT1 is Green.
Acer e-Mill Anilam to AllIn1DC conversion build
Moderator: cnckeith
Re: Acer e-Mill Anilam to AllIn1DC conversion build
If you have FLB connected to INP10, but nothing connected to FLC, then you do not have a complete circuit. That would explain why INP10 is red, and why you get a spindle drive fault message. Install wire #946, from your 0VDC (COM) distribution terminals, to FLC.
-
- Posts: 67
- Joined: Fri Mar 03, 2023 6:56 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: 0008dc111213-1223222881
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Acer e-Mill Anilam to AllIn1DC conversion build
I have FLC connected to TB1/13A
Re: Acer e-Mill Anilam to AllIn1DC conversion build
On your Alt-i screen, is INP10 red or green?
Can you post a current Report?
Can you post a current Report?
-
- Posts: 67
- Joined: Fri Mar 03, 2023 6:56 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: 0008dc111213-1223222881
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Acer e-Mill Anilam to AllIn1DC conversion build
Green...will post a report soon.
-
- Posts: 67
- Joined: Fri Mar 03, 2023 6:56 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: 0008dc111213-1223222881
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Acer e-Mill Anilam to AllIn1DC conversion build
Current report
- Attachments
-
- report_0008DC111213-1223222881_2023-04-04_19-28-15.zip
- (589.21 KiB) Downloaded 3 times
Re: Acer e-Mill Anilam to AllIn1DC conversion build
Hmm. INP10 is green, but you are getting "9028 SPINDLE FAULT!"
You probably need some professional help, either on-site or via TeamViewer.
You probably need some professional help, either on-site or via TeamViewer.
-
- Posts: 67
- Joined: Fri Mar 03, 2023 6:56 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: 0008dc111213-1223222881
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Acer e-Mill Anilam to AllIn1DC conversion build
This error too...Power Fault?
-
- Posts: 3102
- Joined: Tue Mar 22, 2016 10:03 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Boston, MA
- Contact:
Re: Acer e-Mill Anilam to AllIn1DC conversion build
That is not an error. It is showing you the drive bus number. Refer to section 2.4 in the AllIn1DC CNC Control Installation Manual.
Cheers,
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.