Acer e-Mill Anilam to AllIn1DC conversion build

All things related to Centroid Oak, Allin1DC, MPU11 and Legacy products

Moderator: cnckeith

Skunk
Posts: 65
Joined: Fri Mar 03, 2023 6:56 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 0008dc111213-1223222881
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acer e-Mill Anilam to AllIn1DC conversion build

Post by Skunk »

Well the message at startup is gone! Guess I have a working system....well other than the spindle. Who needs a spinning spindle on a CNC mill anyway huh'?

Now to go figure this part out.. Happy Easter
Skunk
Posts: 65
Joined: Fri Mar 03, 2023 6:56 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 0008dc111213-1223222881
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acer e-Mill Anilam to AllIn1DC conversion build

Post by Skunk »

Eureka!

Faulty contactor.

Moved wires from L1/T1 to unused L3/T3.

We have a working spindle now.
Skunk
Posts: 65
Joined: Fri Mar 03, 2023 6:56 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 0008dc111213-1223222881
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acer e-Mill Anilam to AllIn1DC conversion build

Post by Skunk »

It's back?

Machine setup
Not completed.

Machine is not ready
to run.

Contact your dealer.
Attachments
report_0008DC111213-1223222881_2023-04-11_08-21-25.zip
(4.93 MiB) Downloaded 1 time
S-K Machine
Posts: 73
Joined: Mon Jul 05, 2021 5:20 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: A901038
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Lindenhurst, New York

Re: Acer e-Mill Anilam to AllIn1DC conversion build

Post by S-K Machine »

Are you following the installation manual?
You should and not be jumping all over the place.
Page 72

6.13 PERFORMING A SYSTEM TEST
In some versions of CNC12 software, when finished, the main menu will display a message saying “Machine Setup Not
Completed. Machine Is Not Ready To Run. Contact Your Dealer” as shown below.
At this point you will need to run the System Test to clear this message. Documentation on how to perform a system test is
located here. (http://centroidcnc.com/usersupport/supp ... emtest.pdf )
Skunk
Posts: 65
Joined: Fri Mar 03, 2023 6:56 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 0008dc111213-1223222881
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acer e-Mill Anilam to AllIn1DC conversion build

Post by Skunk »

I do not disagree with you at all. My issue is that the test was performed and the message cleared, but then it returned.

Upon attempting to run the tests again I get an error about a missing parameter. When investigating that parameter error I find that the test actually just failed for reason "X or Y". Be nice if they results just said "Failed" and why instead of saying missing parameter. Bit misleading to me.
tblough
Posts: 3072
Joined: Tue Mar 22, 2016 10:03 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Boston, MA
Contact:

Re: Acer e-Mill Anilam to AllIn1DC conversion build

Post by tblough »

Why the test failed is in the test log file.
Cheers,

Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Skunk
Posts: 65
Joined: Fri Mar 03, 2023 6:56 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 0008dc111213-1223222881
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acer e-Mill Anilam to AllIn1DC conversion build

Post by Skunk »

I am starting to get frustrated 3 times today I started with page one. worked through to page 71. Keep getting stuck with 907 X axis travel exceeded. I am on step 5 of 6.11 Software travel limits in the instructions.
Last edited by Skunk on Wed Apr 12, 2023 6:50 pm, edited 1 time in total.
Skunk
Posts: 65
Joined: Fri Mar 03, 2023 6:56 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 0008dc111213-1223222881
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acer e-Mill Anilam to AllIn1DC conversion build

Post by Skunk »

Figured a way around the error.
Skunk
Posts: 65
Joined: Fri Mar 03, 2023 6:56 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 0008dc111213-1223222881
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acer e-Mill Anilam to AllIn1DC conversion build

Post by Skunk »

Now the system "Test"
After pressing Cycle Start
Outputs 306 Job Finished without doing a darn thing.

No errors no movement
Skunk
Posts: 65
Joined: Fri Mar 03, 2023 6:56 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 0008dc111213-1223222881
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acer e-Mill Anilam to AllIn1DC conversion build

Post by Skunk »

Really? That is how you pass the test?

No interaction or acknowledgement on screen?
16813374044456962939375031834218.jpg
Finally I can make parts again?
Post Reply