ATC umbrella AOK

All things related to Centroid Oak, Allin1DC, MPU11 and Legacy products

Moderator: cnckeith

wadyciprian
Posts: 21
Joined: Thu Apr 30, 2020 11:47 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: ACORN-375
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

ATC umbrella AOK

Post by wadyciprian »

I installed a new aok motherboard to my cnc machine with umbrella tool change. I have cntroid 4.2 I have an error when the tool change cycle is releasing the tool. Can someone help me figure out what is happening?
Attachments
report_0008DC111213-0805221349_2022-12-02_16-36-26.zip
(529.14 KiB) Downloaded 5 times
wadyciprian
Posts: 21
Joined: Thu Apr 30, 2020 11:47 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: ACORN-375
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: ATC umbrella AOK

Post by wadyciprian »

I attached a video
Attachments
aok umbrella.mp4
(5.12 MiB) Downloaded 13 times
cncsnw
Posts: 3763
Joined: Wed Mar 24, 2010 5:48 pm

Re: ATC umbrella Oak

Post by cncsnw »

"9055 TOOL CLAMP UNCLAMP FAULT" will happen if the PLC tries to unclamp the tool (turns on OUT22), but the tool-unclamped input switch (INP22) fails to close within 1.5 seconds, or fails to remain closed.

Do you have a tool-unclamped switch?

Do you have it wired to INP22?

Do you see INP22 turn green, on the Alt-i display, when you unclamp a tool? Does it remain green as long as the drawbar is open?
wadyciprian
Posts: 21
Joined: Thu Apr 30, 2020 11:47 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: ACORN-375
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: ATC umbrella AOK

Post by wadyciprian »

When I activate the output with alt-f, the unclamp works perfectly, the same when I press the release tool button.
I understand that the problem is in the time that the solenoid valve remains open.
cncsnw
Posts: 3763
Joined: Wed Mar 24, 2010 5:48 pm

Re: ATC umbrella AOK

Post by cncsnw »

When I activate the output with alt-f, the unclamp works perfectly, the same when I press the release tool button.
When you do that, does INP22 turn green, and stay green?

How long does it take, from the time OUT22 turns on the solenoid, until INP22 turns green?
wadyciprian
Posts: 21
Joined: Thu Apr 30, 2020 11:47 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: ACORN-375
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: ATC umbrella AOK

Post by wadyciprian »

when you ran the m15 command the unclamp tool works perfectly, input 22 changes to green.
wadyciprian
Posts: 21
Joined: Thu Apr 30, 2020 11:47 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: ACORN-375
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: ATC umbrella AOK

Post by wadyciprian »

the problem happens when you executed an m6 tool change
cncsnw
Posts: 3763
Joined: Wed Mar 24, 2010 5:48 pm

Re: ATC umbrella OAK

Post by cncsnw »

I don't see that the logic that leads to "9055 TOOL CLAMP UNCLAMP FAULT" is any different when M15 occurs in an M6 tool change, vs. by itself at the MDI prompt.

Perhaps it is an air supply issue. During an M6 tool change, when the drawbar tries to unclamp, the carousel has been advanced. If your carousel-advance solenoid or cylinder leaks enough air, then perhaps there is insufficient pressure to fully open the drawbar.
wadyciprian
Posts: 21
Joined: Thu Apr 30, 2020 11:47 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: ACORN-375
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: ATC umbrella AOK

Post by wadyciprian »

Can you help me to extend the time that the sensor takes before receiving the signal from the unclamp tool, when I run m6? I don't understand why I have this problem if I press the release tool button, it works fine the same if I run an m15. who can help me?
Attachments
report_0008DC111213-0805221349_2022-12-08_17-35-53.zip
(504.07 KiB) Downloaded 3 times
wadyciprian
Posts: 21
Joined: Thu Apr 30, 2020 11:47 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: ACORN-375
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: ATC umbrella AOK

Post by wadyciprian »

m15 and tool release
Attachments
Video 2022-12-08 at 9.25.03 PM.mp4
tool release
(2.14 MiB) Downloaded 11 times
Video 2022-12-08 at 9.29.07 PM.mp4
m15
(4.03 MiB) Downloaded 6 times
Post Reply