I have my Y axis, and the 4th axis is "paired" to it. The 4th axis has REV enabled. Everything seems to be working fine, but I have concerns I am missing a step. I have seen several references of modifying encoder cable when reversing direction. Does this apply to my setup? DMM made up the cables, I did notice 3 called have black heat shrink on ends, and one has red, but with that said they delivered one a couple weeks after the first 3 were delivered.
Just want to make sure there are no functional issues I will be facing. I have had it air cut some gcode with no issues.
Thanks in advance!
DMM Servo pairing
Moderator: cnckeith
-
- Posts: 9912
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: DMM Servo pairing
Always post a fresh report.repauli1 wrote: ↑Wed Jan 12, 2022 11:28 am I have my Y axis, and the 4th axis is "paired" to it. The 4th axis has REV enabled. Everything seems to be working fine, but I have concerns I am missing a step. I have seen several references of modifying encoder cable when reversing direction. Does this apply to my setup? DMM made up the cables, I did notice 3 called have black heat shrink on ends, and one has red, but with that said they delivered one a couple weeks after the first 3 were delivered.
Just want to make sure there are no functional issues I will be facing. I have had it air cut some gcode with no issues.
Thanks in advance!
Since you posted in the Centroid Oak, Allin1Dc forum, I assume you have OAK (not Acorn?)
If its working, it should be just fine.
Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ
-
- Posts: 156
- Joined: Thu Jul 09, 2020 9:50 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: No
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: DMM Servo pairing
When I post a report, doesn't that give everyone open access to my custom PLC Code, just curious.
Yes Oak, thanks for the reply!
Yes Oak, thanks for the reply!
-
- Posts: 3072
- Joined: Tue Mar 22, 2016 10:03 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Boston, MA
- Contact:
Re: DMM Servo pairing
Yes it does. That's how forums work. We help you. You help others.
Cheers,
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
-
- Posts: 156
- Joined: Thu Jul 09, 2020 9:50 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: No
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: DMM Servo pairing
I understand all that, and mean no disrespect. It's a real pain in the ass getting the report to my pc that has email. I really don't see the importance of a report when it's not a troubleshooting question, but a simple question about the basic install. But not my forum, I will comply in future.
Thanks for the help.
Thanks for the help.
-
- Posts: 9912
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: DMM Servo pairing
You mean getting the report to a PC that has Internet Access?repauli1 wrote: ↑Thu Jan 13, 2022 1:22 pm I understand all that, and mean no disrespect. It's a real pain in the ass getting the report to my pc that has email. I really don't see the importance of a report when it's not a troubleshooting question, but a simple question about the basic install. But not my forum, I will comply in future.
Thanks for the help.
Are you building a proprietary machine for resale? If you want free support, we need to see how you configured CNC12. If you want to hold your secrets close, then I suggest you call Centroid and pay for support.
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ