Oak H1 Power Connector

All things related to Centroid Oak, Allin1DC, MPU11 and Legacy products

Moderator: cnckeith

Post Reply
Robs-shiz
Posts: 15
Joined: Sat Sep 12, 2020 11:18 am
Acorn CNC Controller: No
Allin1DC CNC Controller: No
Oak CNC controller: Yes
CNC Control System Serial Number: 0617200971
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Oak H1 Power Connector

Post by Robs-shiz »

I am in the process of putting all of my CNC components in an enclosure. In the enclosure I have 3 separate ABB power supplies 5V, 12V, and 24V. What I would like to do is connect the oak board to these power supplies and no longer use the mean-well. However upon disconnecting it I quickly grew confused on how to make some of the connections. I have listed the pins below. Each power supply has a + and - terminal. What I think I understand is from the H1 connector pin 1 goes to 12v power supply +, pin 2 ????, pin 3 12 power supply-, pin 4 5V power supply+, pin 5 ???? Possibly 5V power supply -, pin 6 goes to earth ground, please let me know what you guys think. Any advice will be greatly appreciated.

Pin 1: +V2(12V)
Pin 2: COM (12V COM)
Pin 3: -V4 (-12V)
Pin 4: +5V
Pin 5: COM (5V)
Pin 6: ACG (AC GROUND)

Thank you
Robbie
tblough
Posts: 3072
Joined: Tue Mar 22, 2016 10:03 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Boston, MA
Contact:

Re: Oak H1 Power Connector

Post by tblough »

I suggest just keeping the Meanwell supply. It helps separate the controller from EMI and noise generated from other devices connected to your supplies. If you really want to replace the Meanwell, you'll need to add a -12V supply to your system.
Cheers,

Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Robs-shiz
Posts: 15
Joined: Sat Sep 12, 2020 11:18 am
Acorn CNC Controller: No
Allin1DC CNC Controller: No
Oak CNC controller: Yes
CNC Control System Serial Number: 0617200971
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Oak H1 Power Connector

Post by Robs-shiz »

Tblough,

Thank you for the advice, I will reconnect the mean-well power supply.

Robbie
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Oak H1 Power Connector

Post by martyscncgarage »

Robs-shiz wrote: Sun Jun 13, 2021 10:58 pm Tblough,

Thank you for the advice, I will reconnect the mean-well power supply.

Robbie
Don't use the Meanwell Logic power supply for anything else. Follow the schematic.
Contactors would use a separate power supply, solenoids etc.
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
Post Reply