Gentlemen,
I noticed a minor error in your Allinone dc control installation manual page 15 concerning the limit switch defeat. I thought you would like to know. Please correct line 2 it reads funny and one pushes the switches down to defeat. I almost fell into the trap of up! Had I persisted, I would have broken the DIP switch!
I just powered up my Allin1 for the first time a few minutes ago. Wish me well please. I have been working on this since Christmas almost every day, drawing my custom schematics based on yours, ordering parts and wiring. Any needed support will be welcomed. I am ready to get this done an over...
Warm Regards
Mike
Error in Allinone dc control installation manual
Moderator: cnckeith
-
- Posts: 3095
- Joined: Tue Mar 22, 2016 10:03 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Boston, MA
- Contact:
Re: Error in Allinone dc control installation manual
You are not using the latest version of the install manual. https://www.centroidcnc.com/centroid_di ... nuals.html
pg16 wrote:Move the limit switched from the down position to the up position
if the switch is black and from the up position to the down position if the switch is blue.
pg45 wrote:The limit switch defeaters (SW4) on the ALLIN1DC need to be pointed DOWN if SW4 is black and UP if SW4 is blue to be
able to use the limit switches.
Cheers,
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
-
- Posts: 231
- Joined: Mon Feb 07, 2011 8:03 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 1030090103
- DC3IOB: Yes
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: No
- Location: Montvale, NJ
Re: Error in Allinone dc control installation manual
Just to be picky, there is a minor error on page 38 of the AllIn1DC installation manual. The chart refers to 240 VAC two phase input. It should say single phase. Two phase power (90 degree out of phase) is not used in our power distribution system.
-
- Posts: 9914
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: Error in Allinone dc control installation manual
Mike, do be sure to follow this post when asking for help viewtopic.php?f=20&t=383cncot wrote: ↑Fri Mar 19, 2021 12:37 pm Gentlemen,
I noticed a minor error in your Allinone dc control installation manual page 15 concerning the limit switch defeat. I thought you would like to know. Please correct line 2 it reads funny and one pushes the switches down to defeat. I almost fell into the trap of up! Had I persisted, I would have broken the DIP switch!
I just powered up my Allin1 for the first time a few minutes ago. Wish me well please. I have been working on this since Christmas almost every day, drawing my custom schematics based on yours, ordering parts and wiring. Any needed support will be welcomed. I am ready to get this done an over...
Warm Regards
Mike
Follow the latest installation manual as Tom suggested, hopefully you found my video series on an All in One DC installation on YouTube.
Continued luck with your project!
Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ