Haas VF-1 1994 Retrofit Allin1DC - Progress update

All things related to Centroid Oak, Allin1DC, MPU11 and Legacy products

Moderator: cnckeith

Post Reply
manni
Posts: 24
Joined: Sun Jan 24, 2021 2:58 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: none
Location: Walsall - UK
Contact:

Haas VF-1 1994 Retrofit Allin1DC - Progress update

Post by manni »

Hi,

This post is dedicated to my progress so all my updates will be here as I have another post with question where I get stuck. ;) .
Attachments
haas monitor v26.jpg
haas-vf-restore.jpg
manni
Posts: 24
Joined: Sun Jan 24, 2021 2:58 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: none
Location: Walsall - UK
Contact:

Re: Haas VF-1 1994 Retrofit Allin1DC - Progress update

Post by manni »

Got the front control display back from laser cutting and did a test fit of monitor and keyboard before sending it off to powder coating.
will have more update on progress by this weekend.
Attachments
20210209_165229.jpg
20210209_165235.jpg
20210209_152120.jpg
manni
Posts: 24
Joined: Sun Jan 24, 2021 2:58 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: none
Location: Walsall - UK
Contact:

Re: Haas VF-1 1994 Retrofit Allin1DC - Progress update

Post by manni »

Removed old components and labelled the wires. plan is once the display unit comes back from powder coating will start off with Computer unit & Software then all servo motors test before connecting them to Allin1DC.
Attachments
20210204_121338.jpg
20210204_121338.jpg (14.79 KiB) Viewed 364 times
20210204_121259.jpg
20210204_121259.jpg (12.6 KiB) Viewed 364 times
20210204_120945.jpg
20210204_120945.jpg (12.14 KiB) Viewed 364 times
20210204_120937.jpg
20210204_120937.jpg (10.42 KiB) Viewed 364 times
20210204_120927.jpg
20210204_120927.jpg (11.87 KiB) Viewed 364 times
martyscncgarage
Posts: 7883
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
CNC Control System Serial Number: none
Location: Mesa, AZ

Re: Haas VF-1 1994 Retrofit Allin1DC - Progress update

Post by martyscncgarage »

Plow on!
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
manni
Posts: 24
Joined: Sun Jan 24, 2021 2:58 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: none
Location: Walsall - UK
Contact:

Re: Haas VF-1 1994 Retrofit Allin1DC - Progress update

Post by manni »

Hi,

My this week progress. didn't get much time on this, finally at the stage of power up. Still have few more checks.
will take more image of last 2 days work over the weekend.

The estop turned out too small so I have swapped it to the normal size.
Tried my best to keep wiring tidy as best as I can.

any mistakes you guys spot let me know.

Thanks
Manni
Attachments
20210218_133323.jpg
20210218_133306.jpg
20210218_133302.jpg
20210218_133259.jpg
20210218_133256.jpg
20210218_133252.jpg
20210213_144651.jpg
20210213_144600.jpg
20210213_144544.jpg
20210213_144503.jpg
manni
Posts: 24
Joined: Sun Jan 24, 2021 2:58 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: none
Location: Walsall - UK
Contact:

Re: Haas VF-1 1994 Retrofit Allin1DC - Progress update

Post by manni »

Quick Update,
Will upload a better video soon.

Couldn't wait to cut some chips, 1st video without fine DRO adjustments 2nd video after tuning the motors and shows high range to low range gear change before performing ATC orientation.

last few weeks I have learnt a lot, how to edit PLC programme and making macro files. its was intimidating at 1st then after researching and watch Centroid YouTube channel it all made sense and you will be surprise how much information is available on this forum which you can use the use the basic and adjust to your requirements.
I had to create macro and logic for Gear change, Red/green beacon light, cycle start/ feed hold external buttons. Aux button for chip conveyor and Orient solenoid control macro.

will be busy next few weeks with other jobs but would like to fine tune the plc logic or macro's for a quicker gear change and speed up the tool change process.

Thank you all for the help you guys gave in my other posts.

1st video link:


2nd video:


Manni
Attachments
20210330_100317.jpg
20210329_130036.jpg
20210329_130029.jpg
20210329_130024.jpg
20210327_151524.jpg
martyscncgarage
Posts: 7883
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
CNC Control System Serial Number: none
Location: Mesa, AZ

Re: Haas VF-1 1994 Retrofit Allin1DC - Progress update

Post by martyscncgarage »

Outstanding work Manni!
Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
JasonPORC
Posts: 26
Joined: Wed Jan 27, 2021 11:30 am
Acorn CNC Controller: No
Allin1DC CNC Controller: No
Oak CNC controller: Yes
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: none

Re: Haas VF-1 1994 Retrofit Allin1DC - Progress update

Post by JasonPORC »

This is so inspiring to see! I get my oak next week and get to start my build! This is just wonderful to see. Great work man!!!
manni
Posts: 24
Joined: Sun Jan 24, 2021 2:58 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: Yes
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: none
Location: Walsall - UK
Contact:

Re: Haas VF-1 1994 Retrofit Allin1DC - Progress update

Post by manni »

Thanks guys,
Good Luck! Jason with your build.
polaraligned
Posts: 58
Joined: Mon Feb 07, 2011 8:03 pm
Acorn CNC Controller: No
Allin1DC CNC Controller: No
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: Yes
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No
CNC Control System Serial Number: 1030090103
Location: Montvale, NJ

Re: Haas VF-1 1994 Retrofit Allin1DC - Progress update

Post by polaraligned »

Good to see a successful retrofit. You just need to run double that feed rate, and that would be on the lower end for aluminum.
Post Reply