Dip Switch settings

All things related to Centroid Oak, Allin1DC, MPU11 and Legacy products

Moderator: cnckeith

Post Reply
jcsb
Posts: 70
Joined: Mon Jul 09, 2012 5:09 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 929110276
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Dip Switch settings

Post by jcsb »

This is for an ALL-IN-ONE board.
Maybe someone could direct me to documentation showing dip switch location numbers, what each switch does, and the corresponding settings.
I must be blind, but I can't find it anywhere.
tblough
Posts: 3073
Joined: Tue Mar 22, 2016 10:03 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Boston, MA
Contact:

Re: Dip Switch settings

Post by tblough »

Cheers,

Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
jcsb
Posts: 70
Joined: Mon Jul 09, 2012 5:09 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 929110276
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: Dip Switch settings

Post by jcsb »

Thanks, but I have all of those. Either I'm over looking the dip switch settings or there non-existent in the documentation. Now before anyone notes that the manual shows the dip switch, the one shown has to do with servo amp setting. Nothing on the others. Who knows the information could be on the board or cover for the board, but since the DC1 is sitting on top I can't see if it's there or not.
tblough
Posts: 3073
Joined: Tue Mar 22, 2016 10:03 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Boston, MA
Contact:

Re: Dip Switch settings

Post by tblough »

The only two that matter are the servo amp settings and the limit switch override.
Cheers,

Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
cncsnw
Posts: 3766
Joined: Wed Mar 24, 2010 5:48 pm

Re: Dip Switch settings

Post by cncsnw »

The other two banks of DIP switches are for configuring the analog output and the analog input. They matter only if you need to use something other than 0-10VDC.

See the hardware manual that should be appended to the end of the installation manual.

Search for "SW3" and "Analog Output Range Selection", and "SW2" and "Analog Input Range Selection".
jcsb
Posts: 70
Joined: Mon Jul 09, 2012 5:09 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: 929110276
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: No

Re: Dip Switch settings

Post by jcsb »

Yes, that’s exactly what I need. I need to set it to +/-10v. This would allow me to reverse direction. I’ll look again to see if I overlooked the information.
eng199
Posts: 372
Joined: Fri Jan 10, 2014 11:29 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: none
DC3IOB: Yes
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Howard, PA

Re: Dip Switch settings

Post by eng199 »

There are charts on page 7 and 8 of the "user guide" that is tacked on the end of the document linked above.
Post Reply