I have begun gathering information on the installation, setup and configuration of the CNC Depot Spindles with Acorn.
I've personally setup two different machines with them using the Wj200. I have begun compiling my notes to publish for others to benefit from.
Clough42 has those two great videos, but i'm unaware of any summary documents for those that don't want to watch a video.
So, here is my draft PDF. Its is missing photos, let me know what else I am missing, looking forward to hearing your suggestions
CNC Depot Spindle with Acorn and Hitachi WJ200
Moderator: cnckeith
-
- Posts: 7334
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
CNC Depot Spindle with Acorn and Hitachi WJ200
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 104
- Joined: Fri Jan 13, 2023 8:50 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Hopewell NJ
- Contact:
Re: CNC Depot Spindle with Acorn and Hitachi WJ200
I finished up installing the CNC Depot RM40C on my new Acorn/Clearpath/Avid system. I am new to ATC and bought the RM40 Turnkey ATC Spindle Package. What is nice about this system is that it has all the pneumatics done in a separate VFD/Pneumatics box. It has two solenoids to control Clamp and Case pressure, which are wired to an air pressure sensor that sends a spindle fault if pressure drops too low. The VFD in this box is the Automation Direct Durapulse GS20.
Since CNCDepot caters to Avid customers, the VFD box connects to my Acorn control box via 14 pin connectors. The whole system works great. The only change I made was to use one of the unassigned wires to send a VFD Reset signal to the Durapulse to clear the spindle fault. That requires cycling the E-stop button.
Since CNCDepot caters to Avid customers, the VFD box connects to my Acorn control box via 14 pin connectors. The whole system works great. The only change I made was to use one of the unassigned wires to send a VFD Reset signal to the Durapulse to clear the spindle fault. That requires cycling the E-stop button.
Last edited by grossmsj on Sat Feb 24, 2024 8:49 pm, edited 1 time in total.
-
- Posts: 86
- Joined: Sat Feb 27, 2021 10:55 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: E415F6F2C7C9-0211214367
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Quincy, MA
Re: CNC Depot Spindle with Acorn and Hitachi WJ200
I have the same setup and below are the parameter settings on the VFD.
A001=01 (Frequency Source)
A002=01 (Run Command Source)
A003=400hz (Base Frequency)
A004=400hz (use the rating on the nameplate)
A061= 400.0hz (use the rating on the nameplate)
A082=220VAC (use rating on name plate)
B012=10 (Amp Rating for Motor)
H003=2.2 (kW for motor)
H004= number of pole (use rating on name plate)
C036= 1(Alarm signal)
The settings above are for the S30 Spindle using the Hitachi WJ200, if using a different spindle these settings may need to be changed.
Hope this helps
Bill
A001=01 (Frequency Source)
A002=01 (Run Command Source)
A003=400hz (Base Frequency)
A004=400hz (use the rating on the nameplate)
A061= 400.0hz (use the rating on the nameplate)
A082=220VAC (use rating on name plate)
B012=10 (Amp Rating for Motor)
H003=2.2 (kW for motor)
H004= number of pole (use rating on name plate)
C036= 1(Alarm signal)
The settings above are for the S30 Spindle using the Hitachi WJ200, if using a different spindle these settings may need to be changed.
Hope this helps
Bill
-
- Posts: 7334
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: CNC Depot Spindle with Acorn and Hitachi WJ200
thanks Bill!
are you using the Sensorless Vector Feature of the WJ200?
and looking at the manual H004 is asking for the number of motor poles? page 3-104
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 86
- Joined: Sat Feb 27, 2021 10:55 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: E415F6F2C7C9-0211214367
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Quincy, MA
Re: CNC Depot Spindle with Acorn and Hitachi WJ200
H004 is for the number of poles not hZ. A003 & A004 are set according the rated hZ for the motor. My mistake
I noticed in your draft that A062 is set too 83.3. How did you come up with that number?
Bill
I noticed in your draft that A062 is set too 83.3. How did you come up with that number?
Bill
-
- Posts: 7334
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: CNC Depot Spindle with Acorn and Hitachi WJ200
thanks! i edited your post on H004 and corrected it
have you auto tuned and use SV feature?
i haven't setup a 24K rpm unit myself yet so, i asked gary what he was setting A062 for the 24K units and he said 83.3 i assume that is the Hertz needed to meet the low rpm spec on the 24K motor?
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 129
- Joined: Fri Aug 13, 2021 12:25 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: E062346A1C67-0716214939
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: New York
Re: CNC Depot Spindle with Acorn and Hitachi WJ200
I have an S30c and wanted to setup SV feature. I will have to try this out.
Bill
Bill