After upgrading to CNC12 v5.06 my pendant only works at 1x (for all 3 axes).
For the other speeds it doesn't move at all.
Is there some new configuration that I missed? What should I look out for?
WMPG-4 pendant only works at 1x, but not 10x nor 100x
Moderator: cnckeith
-
tblough
- Posts: 3102
- Joined: Tue Mar 22, 2016 10:03 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Boston, MA
- Contact:
Re: WMPG-4 pendant only works at 1x, but not 10x nor 100x
Usually this is due to the control thinking the pribe is tripped. If you will post a report from your machine, that will provide more information for us to help you with.
Cheers,
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
-
VeroEng
- Posts: 5
- Joined: Sun Jan 31, 2021 6:18 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: OCB2B7D3B232-1125204154
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: WMPG-4 pendant only works at 1x, but not 10x nor 100x
Same problem for me (and other issues) since upgrading to 5.06.
-
sakumar
- Posts: 9
- Joined: Thu Feb 25, 2021 4:27 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: WMPG-4 pendant only works at 1x, but not 10x nor 100x
The report is attached above. Thanks.
I do have a KP-3 probe configured, but it was not connected when I tried to use the pendent. I connected it, and toggled it. The triggered / un-triggered messages appeared on the screen, but it didn't fix the issue of the jog speeds > 1.
I do have a KP-3 probe configured, but it was not connected when I tried to use the pendent. I connected it, and toggled it. The triggered / un-triggered messages appeared on the screen, but it didn't fix the issue of the jog speeds > 1.
-
CNCMaryland
- Posts: 369
- Joined: Thu Nov 15, 2018 10:07 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: F045DA7CBF8b-103011290
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: WMPG-4 pendant only works at 1x, but not 10x nor 100x
When you use probe detect, this is the case. You should be able to click the x10 x100 afterwards of plugging in the probe.
-
sakumar
- Posts: 9
- Joined: Thu Feb 25, 2021 4:27 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: WMPG-4 pendant only works at 1x, but not 10x nor 100x
Thanks! Some progress to report. If the probe is left plugged in, then the jogging works normally. But it stops working at 10x and 100x if the probe is then disconnected.CNCMaryland wrote: ↑Tue Sep 12, 2023 2:50 pm When you use probe detect, this is the case. You should be able to click the x10 x100 afterwards of plugging in the probe.
I don't want to have the probe plugged in the entire time. How to fix that?
-
sakumar
- Posts: 9
- Joined: Thu Feb 25, 2021 4:27 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: WMPG-4 pendant only works at 1x, but not 10x nor 100x
OK -- I can see how this is a safety feature -- probe unplugged means 'tripped' so it doesn't allow fast jogging to prevent the probe tip from getting broken. Can I disable this feature?
-
Gary Campbell
- Posts: 2190
- Joined: Sat Nov 18, 2017 2:32 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: Yes
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: Acorn 238
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Bergland, MI, USA
- Contact:
Re: WMPG-4 pendant only works at 1x, but not 10x nor 100x
Reverse the logic on the probe detect input
-
TravisR100
- Posts: 20
- Joined: Thu Jul 27, 2023 11:32 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: None
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: WMPG-4 pendant only works at 1x, but not 10x nor 100x
Was this issue ever solved? I'm having the same problem.
-
centroid467
- Posts: 263
- Joined: Thu Apr 14, 2022 2:46 pm
- Acorn CNC Controller: No
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: No
- CNC11: No
- CPU10 or CPU7: No
Re: WMPG-4 pendant only works at 1x, but not 10x nor 100x
It sounds like the logic is reversed on probe detect input for the others. Have you checked that on your system? Please post a report so we can see what is going on.TravisR100 wrote: ↑Sun Oct 15, 2023 6:16 pm Was this issue ever solved? I'm having the same problem.