Recommendations for PC to run p.m. 940 conversion
Moderator: cnckeith
-
- Posts: 201
- Joined: Tue Dec 21, 2021 1:59 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Recommendations for PC to run p.m. 940 conversion
Well damn looks like I figured out how to attach pictures I guess I’ll upload some more pictures of my build once I get home but here is the message from the ethernet IP adapter
-
- Posts: 237
- Joined: Wed Apr 01, 2020 8:23 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 1702
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Recommendations for PC to run p.m. 940 conversion
Have a look at this pdf. It mentions setting the IP address and should point you in the right direction.
https://www.centroidcnc.com/dealersuppo ... ds/270.pdf
https://www.centroidcnc.com/dealersuppo ... ds/270.pdf
-
- Posts: 201
- Joined: Tue Dec 21, 2021 1:59 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Recommendations for PC to run p.m. 940 conversion
OK just have a larger siding job I’m working on today hopefully later on this evening I’ll be back to the conversion
-
- Posts: 201
- Joined: Tue Dec 21, 2021 1:59 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Recommendations for PC to run p.m. 940 conversion
OK well after walking through that video I have it all communicating with acorn up and operational. But now that I’ve completed all the Centrino wizards and everything from that video it only allows me to move any one of the exercises in a single direction till it stops and then it pulls up drive fault code 931 which I reset it and then I can try another access but then it just pops that code right back up
-
- Posts: 201
- Joined: Tue Dec 21, 2021 1:59 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Recommendations for PC to run p.m. 940 conversion
Yeah no matter what I do in any access it will make the movement and then it sends the 9031 drive fault
-
- Posts: 3098
- Joined: Tue Mar 22, 2016 10:03 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Boston, MA
- Contact:
Re: Recommendations for PC to run p.m. 940 conversion
Chances are it has something to do with drive enble signals and your C86 board. There are many threads going over this common problem.
Cheers,
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
-
- Posts: 201
- Joined: Tue Dec 21, 2021 1:59 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Recommendations for PC to run p.m. 940 conversion
OK I guess I left to find these videos or threads that talk about it, I basically went through the set up directly off of Marty’s video and sent the jumpers like he said, halfway through doing it once I got communication to acorn my axis is moved with no problem, so I continued through his instructions and completed everything he did and now I get movement but calls for an error and a reset every time
-
- Posts: 201
- Joined: Tue Dec 21, 2021 1:59 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Recommendations for PC to run p.m. 940 conversion
OK so I quickly read through some of the posts and I found that switching input number five from normally closed to normally open fixed the situation but is that how it supposed to be or is there something else I need to figure out down the road??