New Build: Frame convert into a working machine
Moderator: cnckeith
-
- Posts: 359
- Joined: Mon Mar 02, 2020 5:07 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Scotland, ON, Canada
New Build: Frame convert into a working machine
Here is where it started. Have made some progress but parts are coming in slowly. Bearings have all been replaced, new paint, some wiring. I removed the welded arm and replaced it with a swing arm.
-
- Posts: 7314
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: New Build: Frame convert into a working machine
right on, thanks for posting.
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 359
- Joined: Mon Mar 02, 2020 5:07 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Scotland, ON, Canada
Re: New Build: Frame convert into a working machine
Thanks Keith
-
- Posts: 359
- Joined: Mon Mar 02, 2020 5:07 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Scotland, ON, Canada
Re: New Build: Frame convert into a working machine
Received my first servo coupler today. I have been searching on Ebay as they are not standard.
-
- Posts: 359
- Joined: Mon Mar 02, 2020 5:07 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Scotland, ON, Canada
Re: New Build: Frame convert into a working machine
Made more progress on the wiring.
-
- Posts: 267
- Joined: Fri Nov 13, 2020 4:12 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: New Build: Frame convert into a working machine
mcmaster or automation direct have been my go-to for couplers. I would check mcmaster if you are still looking for one.
nice progress!
nice progress!
-
- Posts: 359
- Joined: Mon Mar 02, 2020 5:07 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Scotland, ON, Canada
Re: New Build: Frame convert into a working machine
Thanks, I had a look at both places. They don't have anything that will go from 1/2" to 25mm and 40mm. So I am looking for a couple of zero-max 80 series and have they machined. So far no luck yet.
-
- Posts: 359
- Joined: Mon Mar 02, 2020 5:07 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Scotland, ON, Canada
Re: New Build: Frame convert into a working machine
Strange thing when I attached the signal wires to the motor. I began to vibrate hard for about 15 seconds and would not move with cnc12.
Not sure why. It is fine with power and the USB cable. It starts doing this when the signal wire from Acorn is attached.
/
Other 2 couplers arrived.
Not sure why. It is fine with power and the USB cable. It starts doing this when the signal wire from Acorn is attached.
/
Other 2 couplers arrived.
-
- Posts: 267
- Joined: Fri Nov 13, 2020 4:12 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: New Build: Frame convert into a working machine
You have to tune the servos with Teknic's MSP software via the micro usb cable.
They come tuned to no load, so when you connect it to your mill it isnt expecting that load and goes into protective stop
Otherwise check that you wired it correctly
-
- Posts: 359
- Joined: Mon Mar 02, 2020 5:07 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Scotland, ON, Canada
Re: New Build: Frame convert into a working machine
Thanks they are tuned now with load and attached to the machine. But I get drive fault error when a direction arrow is pressed.