Wiring Confirmation

All things related to the Centroid Acorn CNC Controller

Moderator: cnckeith

martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Wiring Confirmation

Post by martyscncgarage »

tuffduck wrote: Tue Jan 18, 2022 12:23 am No I just want to use 1 contactor. Do I need to run 4 wire to output 1
Sketch what you are talking about. I think you need a small second relay for you C86ACCP no fault input
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
tuffduck
Posts: 359
Joined: Mon Mar 02, 2020 5:07 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Scotland, ON, Canada

Re: Wiring Confirmation

Post by tuffduck »

Okay will sketch it out;

tuffduck
Posts: 359
Joined: Mon Mar 02, 2020 5:07 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Scotland, ON, Canada

Re: Wiring Confirmation

Post by tuffduck »

Here is the diagram. I am not sure if terminal blocks are okay or do I need a relay? Thanks
Attachments
ccp wiring.jpg
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Wiring Confirmation

Post by martyscncgarage »

tuffduck wrote: Tue Jan 18, 2022 4:30 pm Here is the diagram. I am not sure if terminal blocks are okay or do I need a relay? Thanks
Diagram is INCORRECT.
You have voltage across those contacts on Relay 1 feeding the Estop relay coil. DO NOT CONNECT C86ACCP No fault to it as you have it shown.
You must add a second relay for your C86ACCP, same coil voltage as your estop contactor. Use its contacts for your C86ACCP No fault
A small din rail relay is fine. Just so long as the coil voltage is the same as your estop contactor.
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
tuffduck
Posts: 359
Joined: Mon Mar 02, 2020 5:07 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Scotland, ON, Canada

Re: Wiring Confirmation

Post by tuffduck »

Okay, so rather than the wires going into the terminal bock they need to go into a relay? The coil in the contactor is 24V.

Which wires would go where? I have never used a relay or contactor before. I will make a new diagram if you can point me in the correct direction.
Thanks
Attachments
61GRgT79umL._SX522_.jpg
firebrick43
Posts: 21
Joined: Sat Jan 08, 2022 10:16 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Wiring Confirmation

Post by firebrick43 »

Most contactors can add an aux set of contacts to the side or front depending on the design. What brand/model of contactor do you have?

Front mount 4 contacts Image

Front mount and side mount single contacts Image
tuffduck
Posts: 359
Joined: Mon Mar 02, 2020 5:07 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Scotland, ON, Canada

Re: Wiring Confirmation

Post by tuffduck »

tuffduck
Posts: 359
Joined: Mon Mar 02, 2020 5:07 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Scotland, ON, Canada

Re: Wiring Confirmation

Post by tuffduck »

martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Wiring Confirmation

Post by martyscncgarage »

tuffduck wrote: Wed Jan 19, 2022 12:59 am Something like these?
https://klocknermoeller.com/xstart/xsta ... ntacts.htm
Yes for the DILM12 frame size (IF that is the part number you purchased in the ebay link you provided)

Attached is a schematic if you want to use a small auxiliary contactor.

Marty
Attachments
Auxillary Contactor_20220119(1).pdf
(1.08 MiB) Downloaded 57 times
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
tuffduck
Posts: 359
Joined: Mon Mar 02, 2020 5:07 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Scotland, ON, Canada

Re: Wiring Confirmation

Post by tuffduck »

Sorry, but now I am very confused. Is that a second quencharc? Are you using 4 terminals on the aux contact?
Post Reply