routeur cnc acorn auto construction
Moderator: cnckeith
-
- Posts: 216
- Joined: Wed Jul 28, 2021 3:54 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: routeur cnc acorn auto construction
https://m.facebook.com/groups/entraide. ... 201871669/
Just need help setting up the axes
Thank you beforehand
Juste besoin d'aide pour configurer les axes
En vous remerciant d'avance
Just need help setting up the axes
Thank you beforehand
Juste besoin d'aide pour configurer les axes
En vous remerciant d'avance
-
- Posts: 9912
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: routeur cnc acorn auto construction
So you got you axis moving. Good
Make SURE you have the steps per motor revolution correct. Then:
Translate and read the Acorn Installation Manual:
https://www.centroidcnc.com/centroid_di ... manual.pdf
Specifically starting on page 78
Make SURE you have the steps per motor revolution correct. Then:
Translate and read the Acorn Installation Manual:
https://www.centroidcnc.com/centroid_di ... manual.pdf
Specifically starting on page 78
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ
-
- Posts: 216
- Joined: Wed Jul 28, 2021 3:54 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: routeur cnc acorn auto construction
Have you looked at the report?martyscncgarage wrote: ↑Tue Jun 14, 2022 9:23 am So you got you axis moving. Good
Make SURE you have the steps per motor revolution correct. Then:
Translate and read the Acorn Installation Manual:
https://www.centroidcnc.com/centroid_di ... manual.pdf
Specifically starting on page 78
Avez vous regarder le rapport ?
-
- Posts: 9912
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: routeur cnc acorn auto construction
Axis Label Motor Encoder Lash Comp. Limit Home Dir ScrewFilardo wrote: ↑Tue Jun 14, 2022 9:34 amHave you looked at the report?martyscncgarage wrote: ↑Tue Jun 14, 2022 9:23 am So you got you axis moving. Good
Make SURE you have the steps per motor revolution correct. Then:
Translate and read the Acorn Installation Manual:
https://www.centroidcnc.com/centroid_di ... manual.pdf
Specifically starting on page 78
Avez vous regarder le rapport ?
mm/rev counts/rev. (mm) - + - + Rev Comp
1 X 5.0000 4000 0.0150 0 0 0 0 N N
2 Y 3.9500 4000 0.0150 0 0 0 0 N N
3 Z 5.0000 2000 0.0000 0 0 0 0 N N
Why is your Z axis show only 2000 encoder counts? Same drive ax X/Y? Should be same encoder count.
Also, if you have belt reduction on your axis, say you have 20/40 teeth or 2:1 reduction then you multiply the ballscrew pitch by that much.
So for X if you have 2:1 belt reduction, 2*5mm you would enter 10 (instead of 5)
Follow the installation manual.
Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ
-
- Posts: 216
- Joined: Wed Jul 28, 2021 3:54 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: routeur cnc acorn auto construction
Ok mercimartyscncgarage wrote: ↑Tue Jun 14, 2022 10:03 amAxis Label Motor Encoder Lash Comp. Limit Home Dir ScrewFilardo wrote: ↑Tue Jun 14, 2022 9:34 amHave you looked at the report?martyscncgarage wrote: ↑Tue Jun 14, 2022 9:23 am So you got you axis moving. Good
Make SURE you have the steps per motor revolution correct. Then:
Translate and read the Acorn Installation Manual:
https://www.centroidcnc.com/centroid_di ... manual.pdf
Specifically starting on page 78
Avez vous regarder le rapport ?
mm/rev counts/rev. (mm) - + - + Rev Comp
1 X 5.0000 4000 0.0150 0 0 0 0 N N
2 Y 3.9500 4000 0.0150 0 0 0 0 N N
3 Z 5.0000 2000 0.0000 0 0 0 0 N N
Why is your Z axis show only 2000 encoder counts? Same drive ax X/Y? Should be same encoder count.
Also, if you have belt reduction on your axis, say you have 20/40 teeth or 2:1 reduction then you multiply the ballscrew pitch by that much.
So for X if you have 2:1 belt reduction, 2*5mm you would enter 10 (instead of 5)
Follow the installation manual.
Marty
-
- Posts: 9912
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: routeur cnc acorn auto construction
Mistake, DIVIDE the pitch by the reduction
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ
-
- Posts: 216
- Joined: Wed Jul 28, 2021 3:54 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: routeur cnc acorn auto construction
I believe that my step problem on the y axis comes from the computer which is not the same
This is the cl86t
While the other x and z axes are cl86y
Je crois que mon problème de pas sur l'axe y viens du calculateur qui est pas le même
Il s'agit du cl86t
Alors que les autres axe x et z sont des cl86y
-
- Posts: 1967
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: routeur cnc acorn auto construction
CL86T is with 5V logic. Use DB25 for DIR and PUL
Uwe
Uwe
-
- Posts: 9912
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: routeur cnc acorn auto construction
Always best to use the same 3 motors and drives. I would replace that odd ball set to match the other two.
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ