vfd A2 series

All things related to the Centroid Acorn CNC Controller

Moderator: cnckeith

martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: vfd A2 series

Post by martyscncgarage »

Votre broche fonctionne sauf que vous obtenez un défaut de broche correct?
Your spindle is working except you get a Spindle Fault correct?

Je vous ai suggéré d'aller dans la page de saisie de l'assistant et de modifier l'état de l'entrée. Cliquez sur le numéro VERT et il deviendra rouge.
I suggested you go into the Wizard input page and change the state of the input. Click on the GREEN number and it will turn red.
SpindleOK Normally Closed.jpg
Cela change l'état de l'entrée de normalement fermée à normalement ouverte.
This changes the state of the input from normally closed to normally open.

Votre VFD ferme ses contacts en cas de défaut. Les contacts de défaut VFD sont ouverts lorsqu'il n'y a pas de défaut. Ouvert=Rouge, Fermé=Vert
Your VFD closes its contacts when there is a fault. The VFD fault contacts are open when there is no fault. Open=Red, Closed=Green

Une fois que vous avez cliqué sur le numéro, il devrait devenir rouge et ressembler à ceci :
Once you click on the number it should turn to red and look like this:
SpindleOK Normally Open.jpg
Voyez où mon doigt pointe dans la première image ci-dessus (en bas de la zone de saisie), traduisez ce texte en anglais. Cela explique ce que je mentionne ci-dessus.
See where my finger is pointing in the first picture above (Bottom of the inputs box), translate that text to English. It explains what I mention above.
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: vfd A2 series

Post by martyscncgarage »

OU changez les contacts utilisés sur votre VFD
LZ=Acorn commun d'alimentation
Si vous utilisez LB, passez à LK pour l'entrée Acorn SpindleOK.

Assurez-vous de programmer cela dans les paramètres pour VFD Fault s'il n'est pas déjà programmé.

OR change the contacts used on your VFD
LZ=Acorn Power Supply Common
If you are using LB, change to LK for Acorn SpindleOK input.

Make sure you program that in parameters for VFD Fault if not already programmed.

Comme vous, j'ai du mal à lire le manuel VFD en français.
Like you, I have trouble reading the VFD Manual in French.
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
Filardo
Posts: 216
Joined: Wed Jul 28, 2021 3:54 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: vfd A2 series

Post by Filardo »

La manipulation que vous m'avez donné et bonne j'ai mis le spindle ok en rouge
Et du coup plus de défaut merci beaucoup
Pour le manuel en anglais voir la pièce jointe en PDF je vous joins aussi un photo de la broche pour savoir ce que je dois mettre dans le pc et le vfd comme valeur
En vous remerciant par avance

The manipulation you gave me and good I put the spindle ok in red
And suddenly no more faults, thank you very much
For the English manual see the attachment in PDF I also attach a photo of the pin to know what I have to put in the pc and the vfd as value
Thanking you in advance
Attachments
IMG_20211103_170501640.jpg
VFD ASKPOWER A131 UserGuide (1).pdf
(6.19 MiB) Downloaded 62 times
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: vfd A2 series

Post by martyscncgarage »

On dirait que vous l'avez en cours.
Le problème était avec les contacts VFD. Vous avez probablement utilisé le mauvais, NO vs NC. COM reste toujours le même et c'est là que va Acorn Power Supply Common.

Sounds like you have it going.
The issue was with the VFD contacts. You likely used the wrong one, NO vs. NC. COM always stays the same and that is where Acorn Power Supply Common goes.

Make sure you read this post on tuning a VFD:
viewtopic.php?f=63&t=1650
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
Filardo
Posts: 216
Joined: Wed Jul 28, 2021 3:54 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: vfd A2 series

Post by Filardo »

martyscncgarage wrote: Wed Nov 17, 2021 4:59 pm Le schéma Acorn VFD est correct. Vous avez besoin d'aide pour connecter les bons fils au VFD et programmer le VFD.

English:
The Acorn VFD Schematic is correct. You need help in connecting the correct wires to the VFD and programming the VFD.
Hello I have the wmp4 which moves 2mm per pulse is this normal
suntravel
Posts: 1967
Joined: Thu Sep 23, 2021 3:49 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 6433DB0446C1-08115074
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Germany

Re: vfd A2 series

Post by suntravel »

Filardo wrote: Mon Jul 04, 2022 12:49 am
martyscncgarage wrote: Wed Nov 17, 2021 4:59 pm Le schéma Acorn VFD est correct. Vous avez besoin d'aide pour connecter les bons fils au VFD et programmer le VFD.

English:
The Acorn VFD Schematic is correct. You need help in connecting the correct wires to the VFD and programming the VFD.
Hello I have the wmp4 which moves 2mm per pulse is this normal
In the Wizard / Axis set the linear Jog Incremet to 0.01, default is 0.02

Uwe
Filardo
Posts: 216
Joined: Wed Jul 28, 2021 3:54 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: vfd A2 series

Post by Filardo »

suntravel wrote: Mon Jul 04, 2022 4:22 am
Filardo wrote: Mon Jul 04, 2022 12:49 am
martyscncgarage wrote: Wed Nov 17, 2021 4:59 pm Le schéma Acorn VFD est correct. Vous avez besoin d'aide pour connecter les bons fils au VFD et programmer le VFD.

English:
The Acorn VFD Schematic is correct. You need help in connecting the correct wires to the VFD and programming the VFD.
Hello I have the wmp4 which moves 2mm per pulse is this normal
In the Wizard / Axis set the linear Jog Incremet to 0.01, default is 0.02

Uwe
The place where I set the screw pitches in winzard
suntravel
Posts: 1967
Joined: Thu Sep 23, 2021 3:49 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 6433DB0446C1-08115074
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Germany

Re: vfd A2 series

Post by suntravel »

Yes.
Filardo
Posts: 216
Joined: Wed Jul 28, 2021 3:54 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: vfd A2 series

Post by Filardo »

Ok merci je regarde ce soir je vous tiens au courant
Filardo
Posts: 216
Joined: Wed Jul 28, 2021 3:54 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: vfd A2 series

Post by Filardo »

suntravel wrote: Mon Jul 04, 2022 4:40 amYes.
Parasites or a wifi key can they shift my origins during machining

Les parasites ou un clé wifi peuvent t'ils décaler mes origines pendant usinages
Post Reply