ether 1616 not recognized <resolved>

All things related to the Centroid Acorn CNC Controller

Moderator: cnckeith

Post Reply
n2xd
Posts: 31
Joined: Sat May 26, 2018 8:01 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 0943
DC3IOB: No
CNC11: No
CPU10 or CPU7: No
Location: Franklin,NC

ether 1616 not recognized <resolved>

Post by n2xd »

Trying to install ether1616 but it is not recognized. Please ignore the dates on the pictures as the camera does not get used much and has to be recharged every time I want to use it. Any help would be appreciated. Thanks.

John
DSC00494.JPG
DSC00495.JPG
DSC00497.JPG
eng199
Posts: 372
Joined: Fri Jan 10, 2014 11:29 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: none
DC3IOB: Yes
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Howard, PA

Re: ether 1616 not recognized

Post by eng199 »

Not showing up in wizard, or something else?

There is a lot of information in this thread:
viewtopic.php?f=60&t=5812&hilit=eth1616
tblough
Posts: 3072
Joined: Tue Mar 22, 2016 10:03 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Boston, MA
Contact:

Re: ether 1616 not recognized

Post by tblough »

You might want to do something about the exposed foil and braid on the shielded wires above your Acorn board before something shorts out.
Cheers,

Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
n2xd
Posts: 31
Joined: Sat May 26, 2018 8:01 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 0943
DC3IOB: No
CNC11: No
CPU10 or CPU7: No
Location: Franklin,NC

Re: ether 1616 not recognized

Post by n2xd »

It's not showing up in wizard.

Everything will be set right I am still trying to get every thing working together.
Richards
Posts: 692
Joined: Sun Sep 16, 2018 9:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: South Jordan, UT

Re: ether 1616 not recognized

Post by Richards »

What lights do you have on your network switch? It looks like jumper A0 is in place, so the board should be at IP address 10.168.41.3. Your PC should be at IP address 10.168.41.1 and your Acorn should be at IP address 10.168.41.2. What happens when you ping those addresses? (See page 4 of the Ethernet 1616 setup guide.)

I cannot see how your power supply outputs are wired to the 1616 board. Verify that you have the proper voltages going from the power supply to the 16X16. (See page 3 of the Ethernet 1616 setup guide.)
-Mike Richards
n2xd
Posts: 31
Joined: Sat May 26, 2018 8:01 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 0943
DC3IOB: No
CNC11: No
CPU10 or CPU7: No
Location: Franklin,NC

Re: ether 1616 not recognized

Post by n2xd »

Thanks for the reply. The fault has been corrected. I had to change the ether port settings(on the Centroid supplied computer ) to the correct ones. Once again thanks for your offer to help.


John
Post Reply