Drive fault 9031 on ACORN CNC12

All things related to the Centroid Acorn CNC Controller

Moderator: cnckeith

Iflyb777
Posts: 30
Joined: Wed May 12, 2021 8:48 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 0035FF98C2BC-0421214705
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Beloit , Ks

Drive fault 9031 on ACORN CNC12

Post by Iflyb777 »

20210608_085035.jpg
20210608_085045.jpg
20210608_085108.jpg
20210608_085102.jpg
Have acron CNC12 and KL 5080D4 driver motor KL 23 31n 1000 from Automation Technology I received it work fine day 1 next day stared CNC 12 move Axies z motor turn just little got drive fault 9031 and getting 7 red flashes on drive, KL manual says 1, the value of position following error is set to small 2, motor wiring error check wiring ,the puzzling thing it work fine first day
One member suggested doing wiring through DB 25 plug, just stared project going to put on small bench lathe
Need help
Thanks Larry
Last edited by Iflyb777 on Wed Jun 09, 2021 10:24 am, edited 1 time in total.
cnckeith
Posts: 7166
Joined: Wed Mar 03, 2010 4:23 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: none
DC3IOB: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Contact:

Re: Drive fault 9031 on ACORN CNC12

Post by cnckeith »

please always post a fresh report.zip when requesting support

and yes, most stepper motor drives perform better on the DB25 connector. use a break out board to make the wiring easier. like the one here.
https://www.centroidcnc.com/centroid_di ... _gear.html
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
Iflyb777
Posts: 30
Joined: Wed May 12, 2021 8:48 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 0035FF98C2BC-0421214705
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Beloit , Ks

Re: Drive fault 9031 on ACORN CNC12

Post by Iflyb777 »

Thanks I will get a report posted
Thanks for the help
Iflyb777
Posts: 30
Joined: Wed May 12, 2021 8:48 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 0035FF98C2BC-0421214705
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Beloit , Ks

Re: Drive fault 9031 on ACORN CNC12

Post by Iflyb777 »

I have order DB25 break out board
here is report
20210609_090321.jpg
20210609_090328.jpg
20210609_090311.jpg
20210609_090406.jpg
20210609_090412.jpg
Iflyb777
Posts: 30
Joined: Wed May 12, 2021 8:48 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 0035FF98C2BC-0421214705
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Beloit , Ks

Re: Drive fault 9031 on ACORN CNC12

Post by Iflyb777 »

just put more picture on ,still no luck
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Drive fault 9031 on ACORN CNC12

Post by martyscncgarage »

You know about the diagnostic screen in CNC12 correct?
Press the Alt i on the keyboard to toggle it on and off
Top line, far left, of virtual LED's are the INPUTS
Second line, far left, of virtual LED's are the OUTPUTS

Now,
When you Start and Reset CNC12 all is well until you try and command a move? When you do, the drive itself is faulting correct?
You said blinking LED's

You also say it was working DAY one but now not. What did you do differently?
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Drive fault 9031 on ACORN CNC12

Post by martyscncgarage »

Also,
You have 1600 steps per motor rev set up in Axis configuration.
Do you have the drive setup for 1600 steps? Post a picture of the dipswitches and please post a link to the drive manual.

Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
Iflyb777
Posts: 30
Joined: Wed May 12, 2021 8:48 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 0035FF98C2BC-0421214705
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Beloit , Ks

Re: Drive fault 9031 on ACORN CNC12

Post by Iflyb777 »

Out of shop for little bit get back with info
Marty thanks for help
Larry
Iflyb777
Posts: 30
Joined: Wed May 12, 2021 8:48 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 0035FF98C2BC-0421214705
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Beloit , Ks

Re: Drive fault 9031 on ACORN CNC12

Post by Iflyb777 »

20210609_095921.jpg
20210609_095935.jpg
20210609_100316.jpg
Iflyb777
Posts: 30
Joined: Wed May 12, 2021 8:48 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: 0035FF98C2BC-0421214705
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Beloit , Ks

Re: Drive fault 9031 on ACORN CNC12

Post by Iflyb777 »

20210609_095921.jpg
20210609_095935.jpg
20210609_100316.jpg
Post Reply