Acorn controller card question

All things related to the Centroid Acorn CNC Controller

Moderator: cnckeith

noel-nogal
Posts: 84
Joined: Sat Feb 20, 2021 12:37 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: (2669)
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acorn controller card question

Post by noel-nogal »

Hi mr. Marty
I have installed a 1616 expansion board to the cnc router, but cnc12 did not detected it, what can i do
tblough
Posts: 3072
Joined: Tue Mar 22, 2016 10:03 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
Location: Boston, MA
Contact:

Re: Acorn controller card question

Post by tblough »

noel-nogal wrote: Wed May 19, 2021 5:22 pm Hi mr. Marty
I have installed a 1616 expansion board to the cnc router, but cnc12 did not detected it, what can i do
You can start by posting some pictures of the install so we can see the Acorn, 1616, power supplies for both and the network switch.
Cheers,

Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
noel-nogal
Posts: 84
Joined: Sat Feb 20, 2021 12:37 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: (2669)
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acorn controller card question

Post by noel-nogal »

The card its showing a segment on the display on, when i remove the power from the switch the display shows the number 2 blinking, the green leds in the switch two flashes and the one corresponding to the ether1616 is steady on
20210519_154206.jpg
20210519_154215.jpg
20210519_154242.jpg
20210519_154206.jpg
]
Attachments
20210519_154306.jpg
20210519_154339_mfnr.jpg
eng199
Posts: 372
Joined: Fri Jan 10, 2014 11:29 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
CNC Control System Serial Number: none
DC3IOB: Yes
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Howard, PA

Re: Acorn controller card question

Post by eng199 »

noel-nogal wrote: Wed May 19, 2021 5:57 pm The card its showing a segment on the display on, when i remove the power from the switch the display shows the number 2 blinking, the green leds in the switch two flashes and the one corresponding to the ether1616 is steady on20210519_154206.jpg20210519_154215.jpg20210519_154242.jpg20210519_154206.jpg]
This is a good sign, it appears the ETH1616 card is working. Center segment means it is ready, but not communicating with CNC12 yet. Error 2 is "no link", which is correct if you turn off the switch.

Make sure the jumper block is on A0 position.

Please start CNC12 with everything connected and post a report. "eth1616log.txt" should contain some clues, as well as other files in the report.
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Acorn controller card question

Post by martyscncgarage »

Along with what Matt (Eng199)is suggesting (Always post a fresh report!),
Unplug and plug back in your Ethernet cables at the switch and to Ether1616. Make sure they are firmly seated in the connectors and no pressure on the cable at the connector.

Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
noel-nogal
Posts: 84
Joined: Sat Feb 20, 2021 12:37 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: (2669)
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acorn controller card question

Post by noel-nogal »

report_1442FC0C7608-0303212669_2021-05-20_08-24-26.zip
(725.97 KiB) Downloaded 122 times
this is the report with the ether1616 connected
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Acorn controller card question

Post by martyscncgarage »

Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
noel-nogal
Posts: 84
Joined: Sat Feb 20, 2021 12:37 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: (2669)
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acorn controller card question

Post by noel-nogal »

Yes i did exactlly what instructions say.
What about the A0 address 10.168.41.3 it say cnc12 automatically identify it but where i can see that addres? Or do i have to replace the ip address in the ethernet adapter, now it is 10.168.41.1 wich is for the acorn
martyscncgarage
Posts: 9912
Joined: Tue Mar 28, 2017 12:01 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: No
CNC Control System Serial Number: none
DC3IOB: No
CNC12: Yes
CNC11: Yes
CPU10 or CPU7: Yes
Location: Mesa, AZ

Re: Acorn controller card question

Post by martyscncgarage »

Go through the instructions and double check everything.
DO NOT CHANGE THE PC's ETHERNET ADDRESS!

Do you know how to use PING?

Type CMD in Windows 10 search box
When you have the Command box open type
Ping 10.168.41.3

See what you get.
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
noel-nogal
Posts: 84
Joined: Sat Feb 20, 2021 12:37 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
CNC Control System Serial Number: (2669)
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No

Re: Acorn controller card question

Post by noel-nogal »

16215296063964609329220850076734.jpg
Post Reply