Hi All,
I have a spare Acorn board that I like to use to test new software releases and different configurations. I have installed 4.6 Mill and 4.6 Router successfully, but I cannot get 4.6 Lathe to install without a persistent "Emergency Stop Detected". This was not a problem with Mill nor with Router. Nothing has changed in the configuration. Just to be clear, I know I must rename the cncm or cnct directories between installations.
I am using 4 DM556 drivers and a Version 3 Acorn board. I load "Leadshine DM Series" boards in the Wizard and match all the settings from one config to the other.
A Report.zip is attached.
Can you see any problem?
Thanks very much,
Gary
CNC12 4.6 Lathe Can't Clear EStop Detected (Resolved)
Moderator: cnckeith
-
- Posts: 111
- Joined: Tue Aug 14, 2018 10:49 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: noneC120192
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
- Location: Denver, CO
CNC12 4.6 Lathe Can't Clear EStop Detected (Resolved)
Last edited by GBCues on Mon Feb 01, 2021 5:22 pm, edited 1 time in total.
-
- Posts: 7166
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: CNC12 4.6 Lathe Can't Clear EStop Detected
look in the error log to see what is causing the estop condition.
also make sure you don't have the input inverted in the Alt i screen
also make sure you don't have the input inverted in the Alt i screen
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 111
- Joined: Tue Aug 14, 2018 10:49 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: noneC120192
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
- Location: Denver, CO
Re: CNC12 4.6 Lathe Can't Clear EStop Detected (Resolved)
Well, it turns out a wire from my EStop to Common came loose that I couldn't see - why is it always the simple stuff??
Righty-Tighty, Lefty-Loosey LOL
You can delete this post if you like.
Righty-Tighty, Lefty-Loosey LOL
You can delete this post if you like.
-
- Posts: 9912
- Joined: Tue Mar 28, 2017 12:01 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Location: Mesa, AZ
Re: CNC12 4.6 Lathe Can't Clear EStop Detected (Resolved)
That's where the DIAGNOSTIC Screen (Alt i) is worth its weight in gold....for testing and observing inputs and outputs and toggling them if needed.
Glad you figured it out.
Marty
Reminder, for support please follow this post: viewtopic.php?f=20&t=383
We can't "SEE" what you see...
Mesa, AZ
We can't "SEE" what you see...
Mesa, AZ