Please Help!! (Resolved)

All things related to the Centroid Acorn CNC Controller

Moderator: cnckeith

Post Reply
Beechdrvr
Posts: 22
Joined: Sun Sep 30, 2018 10:05 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: none
Location: Connecticut

Please Help!! (Resolved)

Post by Beechdrvr »

Anyone's help would be greatly appreciated!

Here's the issue. I am trying to run this F360 program on my Acorn CNC12 Ver4.14.
I keep getting an "Abnormal Job End" after I load the program and then try to Run it. I have always used F360 with success until now. I have a subscription as well.

Here's what I've done to diagnose it so far so this is all I can tell you.
1: I have made a CAM program using INTERCON and that works fine
2: I have loaded previous Fusion 360 programs from the directory and they run as well.
3: I have gone into F360, post processed the same earlier project, but the NEW copy does not work! I look at them in Notepad and they are identical!
4: I have made a simple CAM in F360 thinking maybe my program was to intense for ACORN. That works.

So here we are. Acorn seems to work but there seems a varying degree of uncertainty around Fusion 360.
I have also reloaded the Centroid post processor from Autodesk.

If anyone can look at or load this program to see what result they get, anything would be appreciated. I know that sounds shady loading a program but Im at my wits end try to get this to work.
Thank you for any input in advance.
Doug
Attachments
John Spoke.nc
(229.45 KiB) Downloaded 11 times
report_38D2693C2D16-0727181089_2021-01-12_20-34-37.zip
(273.32 KiB) Downloaded 4 times
tblough
Posts: 1259
Joined: Tue Mar 22, 2016 10:03 am
Acorn CNC Controller: Yes
Allin1DC CNC Controller: Yes
Oak CNC controller: Yes
MPU11 & GPIO4D -w/ 3rd Party Drives: Yes
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: 100505
100327
102696
103432
7804732B977B-0624192192
Location: Boston, MA
Contact:

Re: Please Help!!

Post by tblough »

You're creating a subprogram by using a program number in the rsnge of 9100-9999 without ending it with subprogram return (M99). Read the manual entry for M98.
Cheers,

Tom
Confidence is the feeling you have before you fully understand the situation.
I have CDO. It's like OCD, but the letters are where they should be.
Beechdrvr
Posts: 22
Joined: Sun Sep 30, 2018 10:05 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: none
Location: Connecticut

Re: Please Help!!

Post by Beechdrvr »

ok, thats a start. Honestly I'm new to this so thank you so much. I'll read up on that.
Beechdrvr
Posts: 22
Joined: Sun Sep 30, 2018 10:05 pm
Acorn CNC Controller: Yes
Allin1DC CNC Controller: No
Oak CNC controller: No
MPU11 & GPIO4D -w/ 3rd Party Drives: No
DC3IOB: No
CNC12: Yes
CNC11: No
CPU10 or CPU7: No
CNC Control System Serial Number: none
Location: Connecticut

Re: Please Help!!

Post by Beechdrvr »

THAT DID IT!!
So much to learn. Thank you so much.
Really appreciate it.
Post Reply