The other way is to go into device manager and disable the touchscreen function. Not 100% but I'm pretty certain it was in the "Human Interface" section. You can easily toggle it back on again later.
I did this on mine last week, as I was getting sick of nuisance events. Besides, I almost never use the touchscreen function now that I have an MPG.
Graph function in continuous loop
Moderator: cnckeith
Re: Graph function in continuous loop
That makes sense, because if you watch the line count in the video, it never seems to finish drawing the program (which is over 1100 lines long).
-
- Posts: 370
- Joined: Tue Dec 11, 2018 4:03 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: F045DA80C8B8-0905181172
E415F6F70BC3-0318203049
98F07B91FC6B-0123236802 - DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: UK
Re: Graph function in continuous loop
Guys, using Slodat's example file I have used the following steps to reproduce:
- Home Machine
- Load and Graph Slodat's NC file - Appears normal with no flickering
- Using Part setup, probe using bore cycle (I use the DP-4 tool)
- Disconnect Probe
- Graph Soldat's file - Graph flickering appears
It therefore appears to be connected with Pulsing/Strobing/Flickering issue previously reported which Keith has confirmed as a known issue with v4.50 that will be rectified in the next release
See link viewtopic.php?f=60&t=4478
This is the same issue that Slodat experienced here viewtopic.php?f=60&t=4867
Hope this helps
- Home Machine
- Load and Graph Slodat's NC file - Appears normal with no flickering
- Using Part setup, probe using bore cycle (I use the DP-4 tool)
- Disconnect Probe
- Graph Soldat's file - Graph flickering appears
It therefore appears to be connected with Pulsing/Strobing/Flickering issue previously reported which Keith has confirmed as a known issue with v4.50 that will be rectified in the next release
See link viewtopic.php?f=60&t=4478
This is the same issue that Slodat experienced here viewtopic.php?f=60&t=4867
Hope this helps
Hope this helps
Nigel
"You can lead a horse to water but you cannot force it to drink"
Nigel
"You can lead a horse to water but you cannot force it to drink"
-
- Posts: 135
- Joined: Wed Jul 31, 2019 12:53 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
Re: Graph function in continuous loop
Thank you for the steps to reproduce Nigelo.
This does seem to be linked to the probe Pulsing issue. I did note it acts differently based on if your probe is NO/NC and only happens after performing a probing cycle.
As stated, this particular issue is being worked on and will be resolved next release.
This does seem to be linked to the probe Pulsing issue. I did note it acts differently based on if your probe is NO/NC and only happens after performing a probing cycle.
As stated, this particular issue is being worked on and will be resolved next release.
When requesting support READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
Centroid PLC Tutorial Videos
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
Centroid PLC Tutorial Videos
-
- Posts: 793
- Joined: Thu Apr 12, 2018 11:16 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Graph function in continuous loop
Thank you for the info. Is there a guess on when it will be released?
-
- Posts: 7325
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Graph function in continuous loop
hopefully i'll have a public beta within a week or two, we are in closed group beta testing now.
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html