Been reading about probing cycles, and noticed the Contour pic/button shown on page 71 of the CNC12 manual is missing on my screen even though the F3 Contr button is there and works. Parameter 155 is set to 0 and I have the Digitizing bundle, so I suspect it should be there. Even more strangely, if I click on the blank space where it should be, the Contour screen comes up! Had thought upgrading to the current 4.20.1 might remedy this, but it didn't. Computer was purchased direct from Centroid last summer, and came with v4.18 preinstalled.
Report attached.
Digitize -> Contour button missing
Moderator: cnckeith
-
- Posts: 41
- Joined: Fri Sep 13, 2019 9:38 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Digitize -> Contour button missing
- Attachments
-
- report_3403DE6EC800-0724192318_2020-02-08_11-22-39.zip
- (278.51 KiB) Downloaded 86 times
-
- Posts: 7334
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Digitize -> Contour button missing
thanks for reporting.. i'll look into it.
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 41
- Joined: Fri Sep 13, 2019 9:38 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Digitize -> Contour button missing
Thanks Keith. Only noticed it yesterday in v4.18, upgraded to 4.20.1 this morning and still there. No need to hurry on my account, just seemed goofy.
-
- Posts: 7334
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Digitize -> Contour button missing
yeah, i think i know what going on.. we'll get it displaying properly again!
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html