Hi,
I've got one of the DC powered switches with my Eth1616 which is a welcome addition. Ive been using another switch in the meanwhile but now keen to install this one. Its got two sets of inputs, which do I use on 24V DC please? The docs show the spec of it, not any wiring info. I also dont see any wiring info amongst the Centroid diagrams.
Thanks
Ethernet Switch - Power / Wiring
Moderator: cnckeith
-
Chaz
- Posts: 588
- Joined: Thu Feb 08, 2018 7:57 am
- Acorn CNC Controller: No
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Ethernet Switch - Power / Wiring
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Chaz
- Posts: 588
- Joined: Thu Feb 08, 2018 7:57 am
- Acorn CNC Controller: No
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Ethernet Switch - Power / Wiring
This looks like the same switch, perhaps different label but same connector etc. On this it suggests that V1 and V2 are 2 different sources in case you wanted resilience? So use use V1 - as GND and V1 + as 24V DC?
https://www.amazon.co.uk/MokerLink-Indu ... r=8-5&th=1
https://www.amazon.co.uk/MokerLink-Indu ... r=8-5&th=1
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Centroid_Liviu
- Posts: 442
- Joined: Mon Jul 18, 2011 9:57 am
- Allin1DC CNC Controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
Re: Ethernet Switch - Power / Wiring
Please see the attached schematic for wiring the Switch.
- Attachments
-
- s15004.r2.pdf
- Acorn + Ether1616 wiring schematic
- (167.68 KiB) Downloaded 9 times
When requesting support READ THIS POST first. https://www.viewtopic.php?f=60&t=1043
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Chaz
- Posts: 588
- Joined: Thu Feb 08, 2018 7:57 am
- Acorn CNC Controller: No
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC11: No
- CPU10 or CPU7: No
Re: Ethernet Switch - Power / Wiring
Perfect, thank you, as assumed. Not powered it on yet, still busy rewiring.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)