Hi everyone!
I'm running Swissi's ProbeApp, and finding an issue that my mfunc6 file that I create (in the cncm folder) gets deleted every time I restart CNC12. The Swissi mfunc6.mac Templates are there, but the actual mfunc6 file that actually gets referenced disappears.
Hoping to figure out what is going on!
Thanks!
mfunc6 disappearing after restarting CNC12 <resolved>
Moderator: cnckeith
-
- Posts: 5
- Joined: Thu Mar 07, 2024 8:03 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 54453804251C-0118247882
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
-
- Posts: 2261
- Joined: Fri May 24, 2019 8:34 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7804734C6498-0401191832
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Clearwater, FL
Re: mfunc6 disappearing after restarting CNC12
There are setting in the wizard to tell CNC12 that you are using a custom M6, did you set these?
-
- Posts: 7411
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: mfunc6 disappearing after restarting CNC12
post a fresh report.zip so we can see what version you are running and the rest of your setup.
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 2261
- Joined: Fri May 24, 2019 8:34 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7804734C6498-0401191832
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Clearwater, FL
Re: mfunc6 disappearing after restarting CNC12
Yeah, what Keith said.
-
- Posts: 5
- Joined: Thu Mar 07, 2024 8:03 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 54453804251C-0118247882
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No