Losing connection with open loop steppers. <resolved >
Moderator: cnckeith
-
- Posts: 2333
- Joined: Fri May 24, 2019 8:34 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7804734C6498-0401191832
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Clearwater, FL
Re: Losing connection with open loop steppers. <resolved >
The entire system can run off 220v. Acorn power supply, PC, VFD, etc. Anytime you have more than one power supply tie the negative outputs (common) together. Running everything on 220 makes wiring much easier and saves energy.
-
- Posts: 2295
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Losing connection with open loop steppers. <resolved >
This is the only option for me in Germany
Uwe
-
- Posts: 2333
- Joined: Fri May 24, 2019 8:34 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7804734C6498-0401191832
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Clearwater, FL
Re: Losing connection with open loop steppers. <resolved >
-
- Posts: 360
- Joined: Thu Nov 23, 2017 1:39 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Losing connection with open loop steppers. <resolved >
-
- Posts: 2333
- Joined: Fri May 24, 2019 8:34 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7804734C6498-0401191832
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Clearwater, FL
Re: Losing connection with open loop steppers. <resolved >
Oh, that’s just great, why don’t you just kick me when I’m down?
It’s hard to find 3 phase here, some of the older industrial parks in my area offer it and forget about it at a home shop.
-
- Posts: 2295
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Losing connection with open loop steppers. <resolved >
Next kick, his 3 phase is 400V, like in my homeShawnM wrote: ↑Sat May 25, 2024 7:12 amOh, that’s just great, why don’t you just kick me when I’m down?
It’s hard to find 3 phase here, some of the older industrial parks in my area offer it and forget about it at a home shop.
But hey, you have lower shipping cost from Centroid
Uwe