Machine parameter for Linear encoder input
Moderator: cnckeith
-
- Posts: 67
- Joined: Wed Oct 13, 2021 11:58 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Machine parameter for Linear encoder input
Id like to use a linear encoder scale to measure my ballscrew and compensate, its an Aikron AKM1 (5v RS422). Theoretically i should be able to connect it directly to the Acorn's encoder input since it has the necessary wiring. However i need to find the machine parameter that sets the Acorn's encoder readout to LINEAR instead of rotary/RPM. Centroid can you advise?
-
- Posts: 2226
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Machine parameter for Linear encoder input
Pinout from Aikron is not the same as Centroid encoder port, you must rewire the Aikron DB9 plug.
Parameter for scales are in the manual, to define an axis as linear or rotary is done in the wizard.
Uwe
Parameter for scales are in the manual, to define an axis as linear or rotary is done in the wizard.
Uwe
-
- Posts: 67
- Joined: Wed Oct 13, 2021 11:58 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Machine parameter for Linear encoder input
Good point about the DB9. Will be sure to verify.
Im having difficulty finding the exact parameter in the manual, there are many options related to scales. Any chance you could you point me in the right direction?
Im having difficulty finding the exact parameter in the manual, there are many options related to scales. Any chance you could you point me in the right direction?
-
- Posts: 2226
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Machine parameter for Linear encoder input
Set up the scale in machine setup and use #423 to display the scale position on the DRO.
With Arcorn 6 you can set up scales in the Wizard.
Uwe
With Arcorn 6 you can set up scales in the Wizard.
Uwe
-
- Posts: 528
- Joined: Tue Aug 17, 2021 10:51 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Machine parameter for Linear encoder input
The AIKRON Model:AKM1 Has been Tested at Centroid.
The Signal Type Needs to be the 5v RS422
https://www.aikrondro.com/product/aikro ... -encoders/
I've attached a snip of the DB9 connector of the Aikron and the Changes needed to match the Centroid DB9 Encoder Port.
The Signal Type Needs to be the 5v RS422
https://www.aikrondro.com/product/aikro ... -encoders/
I've attached a snip of the DB9 connector of the Aikron and the Changes needed to match the Centroid DB9 Encoder Port.
-
- Posts: 2226
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Machine parameter for Linear encoder input
AKS is the slim type, pinout is the same as AKM, I have AKS on my machine. Order them with RS422 and they are ok for Acorn6.Joey wrote: ↑Tue May 07, 2024 5:37 pm The AIKRON Model:AKM1 Has been Tested at Centroid.
The Signal Type Needs to be the 5v RS422
https://www.aikrondro.com/product/aikro ... -encoders/
I've attached a snip of the DB9 connector of the Aikron and the Changes needed to match the Centroid DB9 Encoder Port.
Aikron Scale Wiring.png
Ditron RS422 works also.
Thanks for the drawing, printed out an replaced my shitty pencil sketch
Uwe
-
- Posts: 7494
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Machine parameter for Linear encoder input
here is link to the PDF and the CAD file as well
https://www.centroidcnc.com/centroid_di ... erm=aikron
https://www.centroidcnc.com/centroid_di ... erm=aikron
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 67
- Joined: Wed Oct 13, 2021 11:58 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: Machine parameter for Linear encoder input
Does anyone know the encoder counts for this scale (AIKRON AKM-1)? I put 5000 and it seems to work but want to be absolutely sure before i start mapping, AIKRON isn't too responsive...
-
- Posts: 2226
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Machine parameter for Linear encoder input
For a scale with 0.001mm resolution 1000/mm
Uwe
Uwe
-
- Posts: 3
- Joined: Mon May 13, 2024 4:12 pm
- Acorn CNC Controller: Yes
- Plasma CNC Controller: Yes
- AcornSix CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Hickory CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC12: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
Re: Machine parameter for Linear encoder input
scales are measured in mm per pulse, acorn needs pulses per inch/mm. The formula for inches is 25.4/Resolution in mm. in the case of the akm1 it would be 25.4/.001=25400. A formula for Metric would be 1/Resolution in mm. in the case of the akm1 1/.001 = 1000. Using an incorrect number will work on the bench, but if you compare the movement to a scale or test indicator it will not align with the DRO.