Changing router bits mid-job without an ATC
Moderator: cnckeith
-
- Posts: 7554
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: Changing router bits mid-job without an ATC
NPN for Acorn
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
-
- Posts: 180
- Joined: Tue Jul 11, 2023 12:25 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: San Diego CA
Re: Changing router bits mid-job without an ATC
Thanks, Keith, so it idles high and goes low when a tool is sensed.
Does that mean if it uses a mechanical switch, it should be normally-open? That seems contrary for reliability reasons.
Does that mean if it uses a mechanical switch, it should be normally-open? That seems contrary for reliability reasons.
Previous hobby, building hard core sports cars. See http://midlana.com/ and http://kimini.com/
-
- Posts: 2292
- Joined: Thu Sep 23, 2021 3:49 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 6433DB0446C1-08115074
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Germany
Re: Changing router bits mid-job without an ATC
NC and NO works both, mechanical or as NPN. I prefer NC
Uwe
Uwe
-
- Posts: 180
- Joined: Tue Jul 11, 2023 12:25 am
- Acorn CNC Controller: Yes
- Plasma CNC Controller: No
- AcornSix CNC Controller: No
- Allin1DC CNC Controller: No
- Hickory CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: San Diego CA
Re: Changing router bits mid-job without an ATC
Okay, thanks.
Previous hobby, building hard core sports cars. See http://midlana.com/ and http://kimini.com/
-
- Posts: 2333
- Joined: Fri May 24, 2019 8:34 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7804734C6498-0401191832
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Clearwater, FL
Re: Changing router bits mid-job without an ATC
Both of mine are NO because they are wired to the same input so as stated either will work just fine. Many of the very simple ones available are mechanical or conductive anyway so NPN or PNP wont matter.