Acorn Six enable output on H13 and H14...
1. Is it only 5V or capable of 24V as well
2. Is it sinking or sourcing?
AcornSix Enable
Moderator: cnckeith
-
kman1967
- Posts: 108
- Joined: Wed Feb 16, 2022 2:09 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
AcornSix Enable
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
kman1967
- Posts: 108
- Joined: Wed Feb 16, 2022 2:09 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: AcornSix Enable
Update...
Page 40 of the AcornSix Install Manual rev12 shows +5v to the enable + and the enable - going to the H13 and H14 connectors.
but diagram for a Leadshine CS-D1008 show the enable out from the Acorn going to the enb+ on the drive and enable - on the drive going to grnd.
Page 40 of the AcornSix Install Manual rev12 shows +5v to the enable + and the enable - going to the H13 and H14 connectors.
but diagram for a Leadshine CS-D1008 show the enable out from the Acorn going to the enb+ on the drive and enable - on the drive going to grnd.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
cnckeith
- Site Admin
- Posts: 8841
- Joined: Wed Mar 03, 2010 4:23 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: Yes
- Oak CNC controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
- Contact:
Re: AcornSix Enable
page 40 also says. "An example of drive wiring is below. Please consult your schematic for drive specific wiring."
so use.
https://www.centroidcnc.com/dealersuppo ... 147.r2.pdf
so use.
https://www.centroidcnc.com/dealersuppo ... 147.r2.pdf
Need support? READ THIS POST first. http://centroidcncforum.com/viewtopic.php?f=60&t=1043
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
All Acorn Documentation is located here: viewtopic.php?f=60&t=3397
Answers to common questions: viewforum.php?f=63
and here viewforum.php?f=61
Gear we use but don't sell. https://www.centroidcnc.com/centroid_di ... _gear.html
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
kman1967
- Posts: 108
- Joined: Wed Feb 16, 2022 2:09 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: AcornSix Enable
Not sure how the output can be sourcing and sinking, but OK, I'll wire like that and see what happens.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
Centroid_Tech2
- Posts: 118
- Joined: Mon Mar 03, 2014 4:24 pm
- Allin1DC CNC Controller: Yes
- CNC Control System Serial Number: none
- DC3IOB: Yes
- CNC11: Yes
- CPU10 or CPU7: Yes
Re: AcornSix Enable
See page 81 of the AcornSix install manual for a description of the outputs.
Headers H13 and H14 are 5V logic outputs (High = +5VDC , Low= 0V/GND).
Headers H1, H2, and H3 are open collector outputs (sinking).
Headers H13 and H14 are 5V logic outputs (High = +5VDC , Low= 0V/GND).
Headers H1, H2, and H3 are open collector outputs (sinking).
When requesting support READ THIS POST first. viewtopic.php?f=60&t=1043
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
Please ALWAYS post a FRESH report. To make a report: https://www.youtube.com/watch?v=Ecvg0VJp1oQ.
(We pride ourselves on providing timely solid technical support but, without good information we may not be able to help and/or reply until such information is posted.)
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
kman1967
- Posts: 108
- Joined: Wed Feb 16, 2022 2:09 pm
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: none
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
Re: AcornSix Enable
Thanks, completely missed that.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)
-
ShawnM
- Community Expert
- Posts: 2922
- Joined: Fri May 24, 2019 8:34 am
- Acorn CNC Controller: Yes
- Allin1DC CNC Controller: No
- Oak CNC controller: No
- CNC Control System Serial Number: 7804734C6498-0401191832
- DC3IOB: No
- CNC12: Yes
- CNC11: No
- CPU10 or CPU7: No
- Location: Clearwater, FL
Re: AcornSix Enable
No worries, most everyone does.
(Note: Liking will "up vote" a post in the search results helping others find good information faster)